登录
首页 » Windows_Unix » STM32F103CDE

STM32F103CDE

于 2010-05-17 发布 文件大小:2259KB
0 79
下载积分: 1 下载次数: 4

代码说明:

  STM32F103CDE 中文说明书 对开发者 初学者都有好处(STM32F103CDE chinese document~)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 程序及原
    说明:  系统中采用了电压反馈闭环,单片机通过内部软件产生一路SPWM控制信号,然后经过逻辑门变换电路变换成逆变全桥所需的四路驱动信号,再经专用驱动芯片TLP250隔离放大后,分别加到逆变全桥四个IGBT的栅极,进行驱动控制。(The voltage feedback closed loop is used in the system, and the single chip microcomputer generates all the SPWM control signal through the internal software, then transforms the four-way drive signal required by the logic gate transformation circuit into the inverter full bridge, and then adds to the gate of four IGBT of the inverter full bridge after the special drive chip TLP250 isolation and amplification, and carries on the drive control.)
    2019-04-24 18:33:46下载
    积分:1
  • stm32_ADC_own
    the ADC module of STM32F103ZE own.
    2013-08-26 20:42:25下载
    积分:1
  • test7seg
    单片机控制数码管进行数据显示 单个的数码管(SCM data digital tube display)
    2009-03-22 21:45:07下载
    积分:1
  • AVR TLC5615_SIN
    说明:  AVR单片机控制DA芯片TLC5615,输出正玄波(AVR microcontroller controls Da chip TLC5615 to output sine wave)
    2019-10-28 21:11:40下载
    积分:1
  • Flashing-an-LED
    不同頻率閃爍一個LED燈 用sbit 關鍵字 定義 LED到P0.0端口,LED是自己任意定義且容易記憶的符號(Flashing an LED light at different frequencies)
    2011-11-03 10:42:47下载
    积分:1
  • stm32f4-NAND-Flash-USB-mode
    STM32F4 NAND Flash U盘模式操作(STM32F4 NAND Flash USB mode )
    2015-12-18 10:44:30下载
    积分:1
  • shizhong
    基于ARM的万年历,C程序,LPC21X系列(ARM-based calendar, C program, LPC21X series)
    2011-11-18 10:39:44下载
    积分:1
  • GPIO-interrupt-programming
    STM32之GPIO之外部中断程序编写,学习STM32的苦心积累,希望能帮到你。(STM32- External GPIO interrupt the programming, learning STM32 painstakingly accumulated, I hope you can help.)
    2015-03-30 17:51:37下载
    积分:1
  • 640_480yejing
    这是基于立宇泰公司的ARM板开发的彩色液晶图象显示代码,并可以自由切换要显示的图象。(This legislation is based on the Thai-board development of the ARM color LCD image code and the freedom to switch to show that picture.)
    2007-01-04 20:31:29下载
    积分:1
  • ARM-UART
    ARM监视串行口,将接收到的字符发送到字符再发送给串口,即按PC机键盘通过超级终端发送数据,开发板将接收到的数据再返还给PC,在超级终端上显示。(ARM monitors the serial port, the received characters are sent to a character and then sent to the serial port, ie the PC keyboard to send data via HyperTerminal, the board will receive the data and then back to the PC, in the HyperTerminal display.)
    2013-06-03 19:36:48下载
    积分:1
  • 696522资源总数
  • 104049会员总数
  • 30今日下载