网站首页

登录

虚拟示波器

于 2018-01-08 发布文件大小:283KB

 0  199

下载积分: 1 下载次数: 16

我要下载

代码说明：

实现labview 虚拟双踪示波器的波形显示和波形叠加，以及波形参数测量和保存，另外还可以保存波形的点的数据，并可以利用保存的.lvm文件实现波形回显。外加一个简单的滤波器程序。(It realizes the waveform display and waveform superposition of LabVIEW virtual double trace oscilloscope,and the measurement and preservation of waveform parameters.In addition, it also saves data of waveform points, and can save waveform data by using saved.Lvm files. Add a simple filter program.)

文件列表：

虚拟示波器\cvibuild.User Interface Application\build.ini, 3784 , 2013-01-24
虚拟示波器\cvibuild.User Interface Application\Debug\resources.res, 298204 , 2013-01-24
虚拟示波器\cvibuild.User Interface Application\Debug\User Interface Application.exe, 419328 , 2013-01-24
虚拟示波器\cvibuild.User Interface Application\Debug\User Interface Application.nidobj, 127845 , 2013-01-24
虚拟示波器\cvibuild.User Interface Application\dependencies.bri, 4 , 2013-01-24
虚拟示波器\User Interface Application.c, 1879 , 2013-01-24
虚拟示波器\User Interface Application.cdb, 944387 , 2013-01-24
虚拟示波器\User Interface Application.cws, 4659 , 2013-01-24
虚拟示波器\User Interface Application.exe, 419328 , 2013-01-24
虚拟示波器\User Interface Application.h, 2085 , 2013-01-24
虚拟示波器\User Interface Application.prj, 11924 , 2013-01-24
虚拟示波器\User Interface Application.uir, 5780 , 2013-01-24
虚拟示波器\cvibuild.User Interface Application\Debug, 0 , 2013-01-25
虚拟示波器\cvibuild.User Interface Application, 0 , 2013-01-25
虚拟示波器, 0 , 2013-01-25

下载说明：请别用迅雷下载，失败请重下，重下不扣分！

发表评论

0 个回复

LabVIEW
基于labview和声卡的数据采集，声卡的双声道模拟输出，信号的采集与存储，信号的功率谱分析(Power spectrum analysis based on labview and data acquisition card, sound card, two-channel analog output signal acquisition and storage, signal)

2016-03-31 13:54:09下载

积分：1
调频机
晶体的真空调频设备控制VI，通过串口于西门子PLC的通信。实现现场测量参数返回、控制命令下达、动作参数下达PLC、显示测量结果。(I edit the vacuum device control program, the programming language is LABVIEW, thanks to the example of network gods. Upload this document, hoping to provide help for later generations.)

2018-04-28 08:09:42下载

积分：1
LabVIEW课设
虚拟仪器的网络控制 1）、设计一个程序控制8个外设小灯的点亮方式，要求两种方式A:每个小灯间隔时间T，依次亮，时间T可调，并循环。B：先1.3.5.7.9亮隔时间T，2.4.6.8.10亮，并循环，T可调。 2）、要求主面板与硬件的8个小灯同步。 3）、通过网络在另一台计算机上控制此程序的运行（利用LabVIEW的DateSocket技术）((Network control of virtual instruments 1), design a program to control eight peripheral lights lit the way, the requirements in two ways A: each light interval T, followed by bright, time T adjustable, and circulation. B: first 1.3.5.7.9 bright every time T, 2.4.6.8.10 light, and circulating T-adjustable. 2), requires eight small lights of the main panel and hardware synchronization. 3), through the network control of this program running on another computer (using the LabVIEW DateSocket technology)))

2020-12-23 18:09:07下载

积分：1
The-electrical-system-LabVIEW
LabVIEW心电检测系统，主要是滤波信号采集频谱分析显示波形等(LabVIEW ECG detection system is mainly filtered signal acquisition spectrum analysis shows waveforms)

2013-08-29 17:34:25下载

积分：1
visa read
本vi用于从串口读取十六进制数据并保存数据至tdms文件。用户可在第二个循环中根据自己的串口数据格式进行改动。（需要安装visa驱动）(This VI is used to read sixteen hexadecimal data from the serial port, and save data to the TDMS file.)

2017-07-28 11:49:35下载

积分：1
shudu
数独labview实现的源代码,辛苦写出来的(shudu labview source)

2021-01-22 19:38:45下载

积分：1
keller
说明： Keller压力传感器labview源程序(Keller pressure sensor LabVIEW source program)

2020-06-22 23:37:05下载

积分：1
关于LabVIEW的一些程序
伺服电机控制 Modbus命令帧生成程序. 波形记录数据的采集与显示串口通讯 PID控制(Servo motor control. Modbus command frame generation program. Waveform recording. Data collection and display. Serial communication. PID control.)

2018-03-01 12:04:12下载

积分：1
simple-taida-motor-control_labview
控制台达电机旋转的简易例程，其实就是给台达电机发命令哪(Simple console routines of motor rotation)

2013-08-18 13:09:33下载

积分：1
input3D
使用LabVIEW将其他建模软件的3D模型导入到LabVIEW中。(3D models using LabVIEW to other modeling software into LabVIEW.)

2016-06-05 17:23:13下载

积分：1

696522资源总数
104049会员总数
30今日下载