-
BPbox
说明： 2维装箱问题基于遗传算法求解二维装箱问题。。。。(2-D packing problem)
- 2019-05-01 12:20:25下载
- 积分：1
-
不同边界条件下均匀直梁固有频率计算软件源代码
说明： 本软件用于计算不同边界条件下均匀直梁横向、纵向前三阶固有频率。(The software is used to calculate the first three natural frequencies of the transverse and longitudinal direction of a uniform straight beam under different boundary conditions.)
- 2019-12-13 18:34:06下载
- 积分：1
-
基于单片机的智能除湿器 程序源代码
智能除湿器可以实现在封闭空间内保持空气湿度，当湿度传感器采样的信号超过设定值，就一会显示并开启除湿器进行降低湿度，包括主程序、采样程序和显示程序(The intelligent dehumidifier can keep the air humidity in the closed space. When the signal of the humidity sensor exceeds the set value, it will display and open the dehumidifier to reduce the humidity, including the main program, the sampling program and the display program.)
- 2018-06-06 16:51:45下载
- 积分：1
-
fric
Abaqus 子程序，与VS，IVF联用， 用于判断模拟时工件的滑移，粘着(The Abaqus subroutine, combined with VS, IVF, is used to judge the slip and adhesion of the workpiece in the simulation.)
- 2018-01-14 18:34:50下载
- 积分：1
-
gdsx
大学高等数学（同济版）的latext编程课件，可供使用者修改(Latxt Programming Courseware of Higher Mathematics (Tongji Edition) for Users to Modify)
- 2020-10-18 17:07:26下载
- 积分：1
-
涡格法
说明： 采用涡格法估算低速飞机纵向气动特性，包括升力系数、阻力系数及俯仰力矩系数！(It's a great matlab program)
- 2018-05-27 23:15:50下载
- 积分：1
-
DTMF
模拟双音多频(DTMF)拨号系统的MATLAB仿真,形象画出了每个数字键所代表产生的波形(Simulation of Dual Tone Multi-Frequency (DTMF) dial-up system MATLAB simulation, the image drawn by the representative of the number keys for each generated waveform)
- 2020-11-23 20:49:33下载
- 积分：1
-
Mie散射相函数MATLAB源程序
Mie散射相函数MATLAB源程序，求mie散射系数an、bn及散射角等(MATLAB Functions for Mie Scattering and Absorptio)
- 2020-07-19 21:38:46下载
- 积分：1
-
三极管放大电路设计
说明： 三极管放大实验电路，包括固定偏置/分压偏置，需要根据一些参数确定所选用的电阻值，使得三极管工作在放大状态。本程序将电路设计设计成GUI模式，界面上只需要输入电路设计所需参数，根据相关理论推导，给出相关参数的理论值（放大倍数、输入电阻、输出电阻等），指导实验电路搭建。软件搭建在matlab gui上，方便使用
若干参数说明
beta：三极管放大倍数
Ic：集电极电流
Uce：期望CE间电压
UeCof：Re电阻上点电压与Ucc电压比值，一般0.1-0.2
IbCof：Ib上电流与流过Rb1、Rb2电流的比值，一般0.1
ShuntCe：是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
- 2020-04-29 15:11:59下载
- 积分：1
-
smith
等电阻圆、等电导圆、等驻波比圆的画法,有助于了解Smith圆图(The drawing of the equal resistance circle, the equal conductance circle and the standing wave ratio circle will help to understand the Smith circle diagram.)
- 2021-03-31 10:29:09下载
- 积分：1
