登录
首页 » WINDOWS » ECE 4634

ECE 4634

于 2019-04-27 发布
0 130
下载积分: 1 下载次数: 0

代码说明:

说明:  Zero forcing - with interference cancellation

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • flyback
    开关电源反激电路48V/1.5A。电路原理图(Switching power supply flyback circuit 48V/1.5A. Circuit schematic)
    2021-04-12 23:38:57下载
    积分:1
  • dynamic-channel-allocation
    GSM网络的动态信道分配,对于初学这方面的同学有很大帮助(GSM network, dynamic channel allocation, for the beginner in this area of ​ ​ great help to students)
    2011-11-29 09:48:27下载
    积分:1
  • mimo-ofdm 信道估计
    matlab 实现MIMO-OFDM的信道估计(Channel estimation for the implementation of MIMO-OFDM by MATLAB)
    2021-04-13 22:58:56下载
    积分:1
  • CBuilder-JoyStick
    在CBuilder中如何控制游戏手柄,对手柄编程(How to control the game in the CBuilder handle, to handle programming)
    2020-12-03 17:09:25下载
    积分:1
  • Linux C下服务器与客户端之间的文件传输
    实现windows和linux之间的通信 或者 window间通信 linux间通信(Communication between windows and Linux or communication between Linux communication between window)
    2018-02-05 10:37:56下载
    积分:1
  • BER
    这是一个matlab和optisystem联合调试用的误码率计算程序,里面的文件报过一个可以用optisystem7和optisystem13可以打开的OSD仿真图,还有一个MATLAB计算BER的程序。给出了如何设置系统的大纲。从OptiSystem的电信号输入到Matlab组件。当OptiSystem运行时,它将调用Matlab组件中的M文件,处理数据,然后将所得的电信号导出回OptiSystem。然后将输出信号连接到BER分析仪。经过我调试,文件齐全,放心下载(The attached image gives an outline of how the system should be setup. You should start with inputting the electrical signal from OptiSystem into a Matlab component. When OptiSystem runs, it will call the M-file in the Matlab component, process the data, and then export the resulting electrical signal back into OptiSystem.The output signal is then connected to the BER Analyzer.)
    2021-03-18 15:39:20下载
    积分:1
  • 过串口采集下位机信息 smart
    本程序是基于LABWINDOWS/CVI 的,主要是通过串口采集下位机信息,然后显示状态信息并通过串口发送命令字节。(The program is based on LABWINDOWS/CVI.It get message from RS232and display status,then send command by RS232.)
    2011-11-28 21:08:44下载
    积分:1
  • Overcoming_IP_Address_Issues_with_GPRS_Remote_Mon
    GPRS is a communication technology that allows data acquisition systems to overcome the difficulty of cabling for wide area remote sites. GPRS applications are becoming more and more prevalent due to the ease with which they can be implemented, but the dynamic IP address issues associated with GPRS networking continue to frustrate system integrators.
    2011-10-18 04:27:27下载
    积分:1
  • Antenna_polarization_3D.m
    说明:  均匀平面天线阵列的三维极化方向图,matlab语言。(Antenna Polarization for Uniform Planar Array)
    2020-11-25 11:19:32下载
    积分:1
  • OFDM信号频谱感10
    说明:  前已提出的频谱感知方法主要包括匹配滤波器检测、 能量检测、 循环平稳特征检测以及多分辨率频谱感知. 这些方法均为单节点感知方法.然而,在阴影和深度衰落情况下, 单个节点的感知结果并不可靠, 因此, 需要对多个节点的感知结果进行融合,以提高检测可靠性, 即协作感知技术. 文献采用“或” 准则对各个 CR 感知结果进行融合. 文献则提出了基于 D-S 证据理论的协作频谱感知算法,虽然该算法的性能比“或” 准则或“与”准则要好, 但需要存储大量历史信息, 算法的计算复杂度也很高. 文献中分析了采用似然比检测(likelihood ratio test, LRT) 的软判决与采用“与” 准则的硬判决的性能, 结果表明采用软判决的协作感知性能更优(Previously proposed spectrum sensing methods mainly include matched filter detection, energy detection, cyclostationary feature detection and multi-resolution spectrum sensing. These methods are all single node sensing methods. However, in the case of shadow and deep fading, the sensing results of single node are not reliable, so, It is necessary to fuse the sensing results of multiple nodes to improve the detection reliability, i.e. cooperative sensing technology. In the literature, "or" criterion is used to fuse the CR sensing results. In the literature, a cooperative spectrum sensing algorithm based on D-S evidence theory is proposed. Although the performance of the algorithm is better than "or" criterion or "and" criterion, a large amount of historical information needs to be stored, The computational complexity of the algorithm is also very high. In the literature, the performance of the soft decision based on the likelihood ratio test)
    2020-11-19 21:19:37下载
    积分:1
  • 696522资源总数
  • 104042会员总数
  • 18今日下载