登录
首页 » matlab » 路径规划

路径规划

于 2020-03-13 发布
0 128
下载积分: 1 下载次数: 6

代码说明:

说明:  利用mpc实现路径规划,无人驾驶汽车,代码可直接运行(Path planning of driverless vehicle based on MPC model predictive control)

文件列表:

Chapter6_4_3.mdl, 32121 , 2014-05-30
chapter6_2_4.m, 9536 , 2014-05-30
说明.txt, 68 , 2014-05-30
Chapter6_3.m, 14496 , 2014-05-30

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 新建 好压 ZIP 压缩文件
    说明:  整车三自由度汽车模型,在传统二自由度操纵稳定性模型的基础上考虑了纵向力的影响,车速不再为定值。(Based on the traditional two degree of freedom handling and stability model, the three degree of freedom vehicle model considers the influence of longitudinal force, and the vehicle speed is no longer a fixed value.)
    2021-03-16 14:29:21下载
    积分:1
  • 三极管放大电路设计
    说明:  三极管放大实验电路,包括固定偏置/分压偏置,需要根据一些参数确定所选用的电阻值,使得三极管工作在放大状态。本程序将电路设计设计成GUI模式,界面上只需要输入电路设计所需参数,根据相关理论推导,给出相关参数的理论值(放大倍数、输入电阻、输出电阻等),指导实验电路搭建。软件搭建在matlab gui上,方便使用 若干参数说明 beta:三极管放大倍数 Ic:集电极电流 Uce:期望CE间电压 UeCof:Re电阻上点电压与Ucc电压比值,一般0.1-0.2 IbCof:Ib上电流与流过Rb1、Rb2电流的比值,一般0.1 ShuntCe:是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
    2020-04-29 15:11:59下载
    积分:1
  • power_flow_9_bus
    说明:  经典的牛拉法潮流计算matlab程序,IEEE 9 节点、6节点系统 潮流计算(IEEE 9&6 BUS power flow analysis)
    2020-01-25 17:23:28下载
    积分:1
  • ov7620
    说明:  至今几十个经典项目详细的开发文档举例!!(The development of detailed project documentation classic example!!)
    2009-08-29 21:50:08下载
    积分:1
  • forward_dike
    说明:  基于MATLAB编程实现走向无限、延伸无限的薄板状体磁异常正演(Forward modeling of magnetic anomaly of infinite and extended infinite thin plate)
    2019-06-24 09:24:08下载
    积分:1
  • windfarm
    基于PSCAD4.5的双馈感应式风力发电系统仿真,矢量控制(Simulation of doubly fed induction wind power generation system based on PSCAD4.5 and vector control)
    2018-11-02 11:20:50下载
    积分:1
  • radar
    1、目标速度引起的失真,时间膨胀因子10%、chirp中心频率偏移5%。 2、超高速运动对脉冲压缩的影响,多普勒频移补偿(Distortion caused by target speed, time dilation factor 10%, and chirp center frequency offset 5%. Effects of ultra high speed motion on pulse compression and Doppler frequency shift compensation)
    2017-06-03 12:06:47下载
    积分:1
  • 标准Suboff潜艇光体STL模型 suboff-guangt2i
    标准Suboff潜艇光体STL模型,可用于Openfoam、XFlow、Flow-3D等CFD软件的网格生成和数值模拟使用。(The standard Suboff submarine light body STL model can be used for grid generation and numerical simulation of CFD software such as Openfoam, XFlow, Flow-3D and so on.)
    2020-06-27 02:20:02下载
    积分:1
  • Target tracking
    先对线性调频信号的压缩,然后设计了雷达对目标跟踪的源程序。(Firstly, the linear FM signal is compressed, then the source program of radar target tracking is designed.)
    2020-07-26 22:48:41下载
    积分:1
  • tdms数据读取
    批量读取写入TDMS文件,需先建立一个空白TDMS(To read and write to a TDMS file in batches, a blank TDMS must be established first.)
    2021-03-06 10:49:30下载
    积分:1
  • 696524资源总数
  • 103978会员总数
  • 64今日下载