-
Arx1
选取四个点，自动判断是否在一个平面上。同一个平面上。则绘制一个多边形。不在一个平面，则以前三个点为底面，构成一个椎体。支持Move等转换命令，存图与开图，实现Jig交互绘制等。(Four points are selected to automatically determine whether or not they are on a plane. On the same plane. Draw a polygon. If it is not in a plane, the first three points are at the bottom, forming a vertebral body. Support Move and other conversion commands, save and open maps, Jig interactive rendering, etc.)
- 2020-06-16 08:40:02下载
- 积分：1
-
nec_bldc_ver1_IDC_FD_whole_07911
说明： 启航电动自行车控制器软件,已经量产。用于替换晶汇控制器。(BLDC controller for elec-bike)
- 2019-01-19 21:16:31下载
- 积分：1
-
kaimal_spectrum_Liu
MATLAB谐波叠加法模拟风速时程,水平向Kaimal谱密度表达式, 竖直向L-P谱密度表达式(MATLAB harmonic superposition method for simulation of wind speed time history)
- 2018-01-25 03:00:03下载
- 积分：1
-
MXFEM 1.2
本程序为扩展有限元程序，可以模拟裂纹扩展过程，如果内置裂纹开裂速率，可以进行试件疲劳寿命预测。(This program is an extended finite element program, which can simulate the crack propagation process and predict the fatigue life of specimens if the crack rate is in place.)
- 2017-09-26 06:31:32下载
- 积分：1
-
三极管放大电路设计
说明： 三极管放大实验电路，包括固定偏置/分压偏置，需要根据一些参数确定所选用的电阻值，使得三极管工作在放大状态。本程序将电路设计设计成GUI模式，界面上只需要输入电路设计所需参数，根据相关理论推导，给出相关参数的理论值（放大倍数、输入电阻、输出电阻等），指导实验电路搭建。软件搭建在matlab gui上，方便使用
若干参数说明
beta：三极管放大倍数
Ic：集电极电流
Uce：期望CE间电压
UeCof：Re电阻上点电压与Ucc电压比值，一般0.1-0.2
IbCof：Ib上电流与流过Rb1、Rb2电流的比值，一般0.1
ShuntCe：是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
- 2020-04-29 15:11:59下载
- 积分：1
-
PyHum-master
说明： 侧扫声纳图像处理软件，python。浅水底栖生物成像和底物表征的应用(Shallow water benthic imaging and substrate characterization using
recreational-grade sidescan-sonar)
- 2019-01-05 18:30:52下载
- 积分：1
-
TIN_Voronoi
基于c#编程语言生成不规则三角网，能实现画点生成网型(Irregular Triangulation)
- 2018-05-21 16:01:59下载
- 积分：1
-
sanwei-tuoqiu-abaqus
说明： abaqus建立三维椭球模型，主要用于有限元细观力学分析，建立几何模型(Abaqus establishes 3d ellipsoid model, which is mainly used for finite element mesomechanical analysis and geometric model establishment)
- 2020-11-26 21:49:30下载
- 积分：1
-
高阶统计量法微弱信号检测
基于高阶统计量特征的通信系统中微弱信号检测程序(Weak Signal Detection Program in Communication System Based on Higher Order Statistics)
- 2019-06-25 09:16:02下载
- 积分：1
-
ModelC_pure
说明： 采用相场方法，计算纯物质枝晶生长，标记为相场模型C。(Dendrite growth of pure substance was calculated by phase field method, marked as phase field model C.)
- 2020-06-24 02:20:02下载
- 积分：1
