-
利用单片机ATC51和汇编语言来实现交通灯。其中有PROTUES仿真图，和汇编语言来实现的程序。...
利用单片机ATC51和汇编语言来实现交通灯。其中有PROTUES仿真图，和汇编语言来实现的程序。-The use of microcontrollers and assembly language to achieve ATC51 traffic lights. Which PROTUES simulation map, and assembly language to implement procedures.
- 2023-06-27 20:35:04下载
- 积分：1
-
个人电脑组装材料
PC汇编资料大全-PC assembly material greatly entire
- 2022-03-14 15:07:08下载
- 积分：1
-
Realize single
实现单片机模拟iic，从而使单片机控制iic芯片
-Realize single-chip analog iic, thereby enabling single-chip microcomputer control chip IIC
- 2022-11-18 11:55:03下载
- 积分：1
-
6路红外遥控电路，用3010遥控器1
6路红外遥控电路，用3010遥控器1-8键加电源按键。-6-channel infrared remote control circuit
- 2022-08-19 23:04:25下载
- 积分：1
-
一个用汇编语言编写的计算器程序
一个用汇编语言编写的计算器程序-an assembler language calculator program
- 2023-07-02 21:05:03下载
- 积分：1
-
1. 本程序中，首先应输入一个值赋给初始报数上限m，人数n应为任意的，程序应能自动保存出列人的序号并将出列的人所持的密码赋给m，再次作为报数上限，然后删除出列人...
1. 本程序中，首先应输入一个值赋给初始报数上限m，人数n应为任意的，程序应能自动保存出列人的序号并将出列的人所持的密码赋给m，再次作为报数上限，然后删除出列人信息。如此循环，直至所有人都出列为止。
2. 程序以用户和计算机的对话方式执行，即在计算机屏幕上显示“提示信息”之后，由用户在键盘上输入相应数据（即每个人所持的密码），每个人的序号由程序自动分配并存储。
-1. This process should first enter a value assigned to the initial reported that the maximum number of m, the number n should be arbitrary, the procedure should be able to automatically save a number of people out and held out the password assigned to m again reported as the maximum number, and then delete the information out of people. Such a cycle, until all that far out. 2. Procedures to computer users and the implementation of the dialogue, that is displayed on the screen in the computer " message" after the keyboard by the user in the corresponding input data (that is, each person" s password), each individual" s serial number automatically assigned by the procedures and stored.
- 2022-01-31 12:38:49下载
- 积分：1
-
,片选接到p1.5
复位端 p1.4
中断端接到 int0
82c250工作在斜率模式下 ，RS 接51k电阻到地。
2，SJA10...
,片选接到p1.5
复位端 p1.4
中断端接到 int0
82c250工作在斜率模式下 ，RS 接51k电阻到地。
2，SJA1000与82C250的接口，逻辑上为SJA1000输出0（显性位），表现为低点平输出给82C250，则82C250输出
差分的低电平。SJA1000输出1（隐性位），表现为高电平或悬空输出给82C250，则82C250输出悬空状态。
3,周立功的中SJA_BCANCONF.ASM中对输出控制寄存器 的TX0的输出 极性的位的定义不对。
还有里面定义有接收错误标志码，不知道何时用。-, The election received a P1.5-chip client p1.4 interrupt reset int0 82c250 client received in the slope mode, RS then 51k resistor to ground. 2, SJA1000 with the 82C250 interface, logic for SJA1000 Output 0 (dominant bit), showing low level output to the 82C250, while the low-level differential output 82C250. SJA1000 Output 1 (recessive), and the performance of the output is high or left vacant to the 82C250, the vacant state 82C250 output. 3, Zhou Ligong in the SJA_BCANCONF.ASM of output control register TX0 output polarity bit the definition of wrong. Inside the definition also has to receive error flag code, I do not know when to use.
- 2022-06-28 07:07:40下载
- 积分：1
-
汇编程序
汇编程序
- 2022-03-05 10:02:25下载
- 积分：1
-
交通控制MASM程序需要硬件实现
交通控制MASM程序需要硬件实现-traffic control procedures needed hardware
- 2022-04-30 08:53:24下载
- 积分：1
-
一个AD9851的驱动程序。并行时序。现在的程序和原理图…
一个AD9851的驱动。用的并行时序。
现在把程序和电路图发上来，大家帮帮我看看问题出在那里。谢谢了。
要是有做成功的能共享一下电路和程序感激！
main.c
-An AD9851 driver. Timing used in parallel. Now that the procedures and schematics hair up, everyone help me to see the problem there. Thank you. If success has to do to share about the circuit and procedures grateful! main.c
- 2023-03-18 21:55:03下载
- 积分：1
