▍1. 蓝牙4.0 cc2540串口透传源码
蓝牙4.0 cc2540串口透传源码 OSAL 1.3.2协议栈,BLE蓝牙4.0串口透传源码,测试过没有问题,只有这么多,不知道还有写什么,这样说明已经够清楚了吧!!!!!!!
蓝牙4.0 cc2540串口透传源码 OSAL 1.3.2协议栈,BLE蓝牙4.0串口透传源码,测试过没有问题,只有这么多,不知道还有写什么,这样说明已经够清楚了吧!!!!!!!
用于速度控制,对智能车进行速度控制,能够在速度稳定的基础上,加大速度,不会使车跑离赛道,同时稳定车速,用于飞思卡尔
说明: 基于CC2530实现的手势传感器实现,包含zstack的组网工程(短地址组网)(The realization of gesture sensor based on CC2530, including the networking project of zstack)
说明: 基于低功耗单片机msp430实现的modbus RTU通讯(Modbus RTU communication based on low power MCU MSP430)
充电桩通信规约代码,根据国标进行编写,使用国内大部分电动充电车。(Charging pile communication protocol code, compiled according to national standards, using most domestic electric charging vehicles.)
这是一个QR解码过程,移植到STM32,但是存在内存泄漏。(This is a QR decoding process that is ported to STM32, but there is a memory leak.)
MSP430FR4133用户指南文档编程必备(MSP430FR4133 User Guide Document Programming Requirements)
说明: MSP430FR4133用户指南文档编程必备(MSP430FR4133 User Guide Document Programming Requirements)
使用2个ZigBee节点组网,A做协调器,B做终端节点,PC机通过串口连接A,A协调器通过串口(发送命令)操控B终端节点写入和读取NV数据,NV数据为B终端节点指示灯的闪烁的时间间隔。(Two ZigBee nodes are used to form a network, A is used as coordinator, B is used as terminal node, PC is connected to A through serial port, A coordinator controls B terminal node to write and read NV data through serial port (sending commands). NV data is the flashing time interval of B terminal node indicator.)
说明: 使用2个ZigBee节点组网,A做协调器,B做终端节点,PC机通过串口连接A,A协调器通过串口(发送命令)操控B终端节点写入和读取NV数据,NV数据为B终端节点指示灯的闪烁的时间间隔。(Two ZigBee nodes are used to form a network, A is used as coordinator, B is used as terminal node, PC is connected to A through serial port, A coordinator controls B terminal node to write and read NV data through serial port (sending commands). NV data is the flashing time interval of B terminal node indicator.)
协调器和终端节点通过串口连接PC机,相互通讯,串口助手上可以显示(Coordinator and terminal node connect PC through serial port, communicate with each other, and can be displayed on serial assistant.)
说明: 协调器和终端节点通过串口连接PC机,相互通讯,串口助手上可以显示(Coordinator and terminal node connect PC through serial port, communicate with each other, and can be displayed on serial assistant.)
最初始的IAR编程(包含ccs,gcc的软件的初始程序)(Initial IAR Programming (Initial Programming of Software Containing ccs, gcc))
说明: 最初始的IAR编程(包含ccs,gcc的软件的初始程序)(Initial IAR Programming (Initial Programming of Software Containing ccs, gcc))
说明: msp产生spwm波程序,通过对PWM的产生方波,然后spwm技术生成正弦波(The program of generating SPWM wave by MSP)
说明: 基于STM32F103单片机的lora 通讯模块编程(Programming of Lora communication module based on STM32F103)
说明: 最简单的功能:1,串口轮询发送,中断发送及定长接收,DMA传输。2,ADC转换。外加一点对于代码的理解和注意事项。 本次是基于STM32CUBEMX,IAR,MDK_V5制作的代码,(The simplest functions: 1. Serial polling sending, interrupt sending and fixed-length receiving, DMA transmission. 2. ADC conversion. Add a little bit of understanding and attention to the code. This is based on STM32CUBEMX, IAR, MDK_V5 code.)
CAN通讯控制LED和继电器(单片机STM8,开发环境IAR)(CAN communication control LEDs and relays)