▍1. CS8900A
基于F2812的以太网芯片CS8900A的C程序,基于UDP协议的网络传输。(F2812 s Ethernet the chip CS8900A C program, network transmission based on UDP protocol.)
基于F2812的以太网芯片CS8900A的C程序,基于UDP协议的网络传输。(F2812 s Ethernet the chip CS8900A C program, network transmission based on UDP protocol.)
TMS320F2812驱动cs8900A以太网驱动程序(TMS320F2812 driver CS8900A Ethernet driver)
TEF6686带DSP收音 C语言完整工程实例 ,可直接移植应用。(TEF6686 with DSP radio engineering instance)
TI DSP TMS320VC5509A的SDRAM、I2S、DMA等的接口程序。(TI DSP TMS320VC5509A of SDRAM, I2S, DMA interface procedures.)
DSP28335 EPWM DSP28335 EPWM参考程序设计 电机控制(DSP28335 EPWM reference program design)
DSP28335 脉冲编码控制 PWM电平输出可控制输出电平(DSP28335 pulse encoder output level control PWM output level can be controlled)
三相六拍直流无刷电机驱动固件,采用的TI的方案,已经用在我们公司的无刷圆锯上面了。特共享出来换积分(This is the driver for BLDC motor ,this firmware has been used on our BLDC product.)
DSP 快速傅立叶变换 c语言实现的........(dsp FFT 32*32 c language relize ........)
麦克风阵列波束成型算法,使用C语言写成,易于移植到DSP上(Microphone array beamforming algorithm, written in C language, easy to transplant to DSP)
DSP的SVPWM产生示例,可以学习SVPWM的编程思想和编译方法,能直接移植到28335中应用。(DSP-SVPWM example, can learn the SVPWM programming ideas and methods of compiling, can be directly ported to 28335 in the application。)
VIENNA整流器闭环控制函数实现,利用2812DSP实现(The colse-loop control of VIENNA rectifer based on the DSP of TMS320F2812)
基于F2812的维也纳VIENNA电源程序。本程序根据三电平六开关(Vienna)整流器的工作模态,结合两电平空间矢量(SVPWM)的工作原理,介绍了Vienna整流器SVPWM控制采用两电平SVPWM控制等效的方法。本文提出了一种适用于各种负载条件下的中点电位控制算法。(Based F2812 Vienna VIENNA power program. This procedure based on three-level six-switch (Vienna) rectifier operational modal, combined with the two-level space vector (SVPWM) works, describes the Vienna rectifier SVPWM control method uses two-level SVPWM control equivalent. This paper presents a suitable under various load conditions midpoint potential control algorithm. )
TI dsp的spi编程例子,基于keystone架构,很好的入门资料(example of program spi in dsp )
TI dsp的spi编程例子,基于keystone架构,很好的入门资料(example of program spi in dsp )
配置C6678的GPIO中断,把中断向量表映射到12个可屏蔽中断里(C6678 configuration of GPIO interrupts, the interrupt vector table is mapped to 12 maskable interrupts in)
1.EMIF 接口 TMS320F28335DSP 的扩展存储器接口(EMIF)用来与大多数外围设备进行连接,典型应用 如 连接片外扩展存储器等。这一接口提供地址连线、数据连线和一组控制线。ICETEK–F28335-A 将这些扩展线引到了板上的扩展插座上供扩展使用。 2.液晶显示模块的访问、控制是由28335ADSP 对扩展接口的操作完成。 控制口的寻址:命令控制接口的地址为 0x208001,数据控制接口的地址为0x208003 和 0x208004,辅助控制接口的地址为0x208002。 3.显示控制方法: -液晶显示模块中有两片显示缓冲存储器,分别对应屏幕显示的象素,向其中写入数值将改 变显示,写入“1”则显示一点,写入“0”则不显示。(The 1.EMIF interface Extended TMS320F28335DSP memory interface (EMIF) is used to connect with the most peripheral equipment, typical application Such as The connecting piece of extended memory. This interface provides the address lines, data lines and a set of control line. ICETEK- F28335-A The extension line to the extension socket for plate on the expansion of the use of. 2 liquid crystal display module access, control by the 28335ADSP to the extended interface operation is complete. Addressing control port: Command and control interface address 0x208001, the address data control interface for 0x208003 and 0x208004, auxiliary control interface address for 0x208002. 3 display control method: - liquid crystal display module with two display buffer memory, respectively corresponding screen pixel, writing values will be changed to the Change display, write "1" shows a little, write "0" are not displayed.)
说明: TI F28335 的串口通讯程序;以测试过,可以放心使用。(TI F28335 Serial Communication procedures to test, and can be assured that use.)