登录
首页 » matlab » QPSO_RBF

QPSO_RBF

于 2011-03-24 发布 文件大小:4KB
0 260
下载积分: 1 下载次数: 1

代码说明:

说明:  采用一种量子粒子群算法来对RBF网络进行优化(Using a quantum particle swarm algorithm to optimize the RBF network)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • ansys5
    利用ansys计算的应力结果,求出截面内力,再利用材料力学公式求等效应力(此例是求坝基面的等效应力)(ANSYS calculated using the stress results, obtained cross-section of internal forces, and then use the formula for the mechanical equivalent stress (in this case is to strive for the dam foundation surface equivalent stress))
    2007-12-12 20:00:10下载
    积分:1
  • rsjicun
    建立了基于matlab语言的移位寄存器的仿真模型,通过了系统验证。(Matlab language is established based on the simulation model of the shift register through the system validation.)
    2010-09-27 15:48:15下载
    积分:1
  • specfun
    Funciones varias para Matlab
    2011-10-31 00:47:31下载
    积分:1
  • MISON
    The Comparison in capacity between SISO and MIMO
    2015-04-04 09:57:59下载
    积分:1
  • LyapunovExponents_wolf
    说明:  利用wolf法求取Lyapunnov指数,并绘制图形(Method used to obtain Lyapunnov wolf index, and draw graphics)
    2010-04-27 22:34:08下载
    积分:1
  • asymotor_stator
    三相异步电机matlab仿真模型,能够实现三相异步电机的仿真。(Three-phase asynchronous motors matlab simulation model enables simulation of three-phase asynchronous motors.)
    2015-01-13 11:17:38下载
    积分:1
  • Antenna-near-metallic-cylinder
    Antenna near conducting cylinder-Analytic and Numeric(FDTD)
    2011-10-01 18:08:02下载
    积分:1
  • f-score
    此文档为word文档,给出了F-score的数学计算公式,并将公式用MATLAB写成程序(This document is a word document, gives the F-score mathematical formulation, and the MATLAB program of computing F-score.)
    2013-06-19 11:01:30下载
    积分:1
  • chirpfrequence
    基于chirp信号和Multitone信号的频率特性测试方法研究,采用MATLAB仿真,是最新的研究成果。(Based on the chirp signal and the signal frequency characteristics Multitone testing methods study using MATLAB simulation, is the latest research results.)
    2009-03-12 15:45:41下载
    积分:1
  • matlab1
    控制工具箱与SIMULINK软件应用:系统对象为G(s)=4/s(s+2) PI补偿器K1(s)=(s+1)/s K2(s)=(s+0.5)/s a 若由K1(s)与 G(s)串联组成的单位反馈系统,称为系统A。 b 若由K1(s) 放置在G(s)的反馈通道称为系统B。 c 若由K2(s)与G(s)串联组成的单位称为系统C,绘制上述每一种情况的阶跃响应与斜坡响应,求每一种情况下的系统阶跃响应误差与斜坡响应误差,并与理论分析结果进行比较。 (Control toolbox and SIMULINK software application: system object for G (s) = 4/s (s+ 2) PI compensator K1 (s) = (s+ 1)/s K2 (s) = (s+ 0.5)/s If a by K1 (s) and G (s) series of feedback system of the unit, known as a system a. B if the K1 (s) placed in G (s) feedback channel called system b. If c by K2 (s) and G (s) series of unit is called system c, draw the above each kind of condition of step response and slope response, for each of these cases system step response error and slope response error, and the results were compared with theoretical analysis.)
    2012-04-19 14:43:49下载
    积分:1
  • 696518资源总数
  • 106155会员总数
  • 8今日下载