登录
首页 » matlab » zr

zr

于 2010-06-23 发布 文件大小:3KB
0 217
下载积分: 1 下载次数: 0

代码说明:

说明:  用窗函数法设计一个能对模拟信号进行滤波的线性相位FIR低通滤波器。抽样频率为 kHz,通带截止频率为 kHz,阻带截止频率为 kHz,要求阻带最小衰减 dB。为了降低运算量,所设计滤波器的阶数要尽可能的低(With the window method to design a filter to the analog signals of linear phase FIR low-pass filter. Sampling frequency is kHz, passband cutoff frequency kHz, stopband cutoff frequency of kHz, the minimum required stopband attenuation dB. To reduce the computation, the order of the filter designed to be as low as possible)

文件列表:

zr.doc,20992,2010-06-23

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • MATLAB-OFDM
    说明:  基于MATLAB的OFDM系统仿真分析 pdf格式,不错(MATLAB-based simulation analysis of the OFDM system pdf format, good)
    2008-11-03 09:16:56下载
    积分:1
  • erciqumian2
    用matlab实现二次曲面图绘制,用来绘制曲线图(Draw a graph quadric)
    2013-08-17 21:53:03下载
    积分:1
  • bizhangrobot
    势场法实现移动机器人的避障导航 matlab开发 无需密码解压(Potential field robot obstacle avoidance)
    2011-07-19 12:28:18下载
    积分:1
  • matlab
    image to text and ocr
    2013-12-08 19:19:57下载
    积分:1
  • adaboost
    Adaboost是一种迭代算法,其核心思想是针对同一个训练集训练不同的分类器(弱分类器),然后把这些弱分类器集合起来,构成一个更强的最终分类器(强分类器)。 load clouds [test_targets, E] = lijsada_boost(patterns, targets, patterns, 100, Stumps ,[]) train_patterns 每列为一样本 train_targets 每列为一样本目标 100 :Number Of Iterations Stumps: Weak Learner Type Learner s parameters :[] adaboost +stumps testRightR = 0.7522(Adaboost is an iterative algorithm)
    2014-01-20 13:05:34下载
    积分:1
  • turbo_matlab
    Turbo码编码译码器的研究及其MATLAB实现.(TUrbo)
    2010-05-14 19:40:21下载
    积分:1
  • phasetree
    利用matlab模擬phasetree的情況(using Matlab simulation of phasetree)
    2007-05-02 20:39:24下载
    积分:1
  • Simulink_rus
    similunk book about rus for advanced simulation and modeling
    2013-10-07 16:42:12下载
    积分:1
  • BatchSimulation
    As we know, the energy needed for sensors should be electrical. So the rst step before start to work is to convert environmental energy to electrical one. Inside the node there are dierent components for sensing the area, collecting data and processing the data. So the main dierent part of this kind of nodes, in compare of WSN nodes, is the power part. Once the stored energy reach to a certain amount, the power supply for micro controller and transceiver will start to work. They will continue to work until they have energy, as soon as the energy nish, they stops and energy storage device start to work to save energy again. The other fact should be consider about EH-WSN node is that the available energy can change in dierent nodes. So every node has its own harvesting rate.
    2013-07-20 14:34:56下载
    积分:1
  • threesemi
    Three phase 6-pulse semi controlled rectifier simulation using matlab simulink
    2014-01-29 17:53:48下载
    积分:1
  • 696516资源总数
  • 106459会员总数
  • 0今日下载