登录
首页 » matlab » multipath

multipath

于 2010-06-25 发布 文件大小:1138KB
0 67
下载积分: 1 下载次数: 115

代码说明:

  多径仿真,希望对初学者有所帮助,本人亲自编写的呵呵(Multi-path simulation, want to help beginners, I am personally prepared Ha ha)

文件列表:

新建文件夹
..........\DCT-BASED%2BPHASE%2BCORRELATION%2BMOTION%2BESTIMATION.pdf,312311,2010-06-24
..........\dll编程.pdf,975985,2010-06-24
..........\MATLAB编译产生的DLL.htm,29807,2010-06-24
..........\testNCC3.m,2210,2010-06-24
..........\多径效应.rar,2008,2010-06-24

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Nokia-5110LCD-panel-data
    诺基亚5110LCD&PCD8544IC编程,包括Datasheet、驱动程序例子和应用等等。(Nokia 5110 LCD & PCD8544IC programming, including Datasheet, driver examples and application and so on.)
    2013-12-06 15:21:43下载
    积分:1
  • microbial--fuel-cell
    一些关于微生物燃料电池的英文文献,在网上不能免费下载。(Some of the English literature on microbial fuel cells can not be downloaded free of charge online.)
    2020-10-21 11:57:23下载
    积分:1
  • PWMInversorZVS.X
    code PWM for Inverter Full BRIGTH
    2015-06-20 03:19:42下载
    积分:1
  • MouseRotateApp
    通过鼠标可以控制图象的宣战和显示通过鼠标可以控制图象的宣战和显示(macheng)
    2009-05-17 00:18:07下载
    积分:1
  • 51keilssd1289tft
    51单片机keilssd1289tft触摸彩屏(The 51 SCM keilssd1289tft color touch screen)
    2012-09-18 08:08:54下载
    积分:1
  • 实验四 定时器应用 秒表
    基于stm32f103zet6的万年历设计(Calendar design based on stm32f103zet6)
    2020-07-01 15:00:01下载
    积分:1
  • FIR_filter
    说明:  Fir_filter stm32,keilC v5
    2020-07-13 10:41:53下载
    积分:1
  • learnhongwai
    智能红外遥控学习程序,基于51单片机的学习机。(Intelligent infrared remote learning program, based on 51 SCM learning machine. )
    2012-11-24 17:06:51下载
    积分:1
  • PrivilegedActionException
    PrivilegedActionException wraps exceptions which are thrown from within privileged operations.
    2014-06-12 12:05:28下载
    积分:1
  • 200711-0054-05
    TMS28335初始化完成之后, 1、 先DDS产生73.35hz的方波。(问流量管固定频率) 2、 乘法器的另一个数字端输入乘数直接给一个固定值(按照5v),系数是固定的就是对应PID输出的那个接口,串行十二位信号输出(需要先定好一个GPIO接口)。 3、 再延迟一定的时间0.1s或其他时间之后,开始ad采集信号,分别采两路AD信号,此时不稳定(为什么要等到一定的幅值才开始采集AD信号) 4、 选择250点估计一个频率,频率估计的方法采用计算峰值次数的方法或者过零点,总之是为了保证精度采用时域估计的算法,这一块主要是一个扫频子程序,计算频率共振点。 5、 之后改变DDS的输出频率,循环对512点的数据进行扫频的处理 6、 频率控制完成之后,就可以缓慢降低PID控制输出的参数,此时暂时不计算频率,通过不断调整系数使AB的幅度保持在1 的范围内。 7、 测试幅度控制稳定之后a、采用幅度和频率同时控制b。采集数据进入频率估计和相位差估计的后续程序的大循环 8、 注意:采样和控制是同时进行的,所以要设置中断,以及看懂AD的程序,以及内部存储以及数据处理资源的分配。 (TMS28335 initialization is complete, 1, the first DDS generated square wave of 73.35hz. (Q flow tube fixed frequency) 2, another digital side of the multiplier input multiplier directly to a fixed value (in accordance with 5v), the coefficient is fixed corresponding PID output interface, serial twelve signal output (need to be a good one GPIO interface). 3, and then after a certain time delay 0.1s or other time, ad signal acquisition were collected two AD signal instability (Why wait until a certain amplitude began collecting AD signal) 4, 250 point estimate a frequency, frequency estimation method using the method of calculation of the number of peak or zero crossing, in short, in order to ensure the accuracy of time-domain estimation algorithm, this piece is a sweep subroutine to calculate the frequency resonance point. 5, after the change of the output frequency of the DDS data of 512 points, the loop processing Sweep 6, after the completion of the frequency control, it can sl)
    2013-04-07 15:03:14下载
    积分:1
  • 696518资源总数
  • 104225会员总数
  • 32今日下载