-
Gui_scripter
由VB6.0 gui生成matlab的m文件，可由VB对象生成等价对应的matlab对象(Creates an M-File from a Visual Basic 6.0 Project GUI Interface
)
- 2009-05-01 10:40:38下载
- 积分：1
-
AFC
说明： 频率偏差估计由信道参数估计和频率偏差估计两部分组成 环路滤波器设计(Frequency offset is estimated by the channel parameter estimation and frequency offset is estimated that two-part loop filter design)
- 2009-08-28 10:55:42下载
- 积分：1
-
ANFIS_BP-master
说明： 自适应模糊神经网络的一个模型matlab语言实现(ANFIS_BP-master Substractive clustering algorithm)
- 2019-04-02 15:54:52下载
- 积分：1
-
Smart-Antenna-System
输入信号到达角度可自行设置，在ESPRIT、MUSIC算法下实现了宽带波束形成(Input signal reaches the point of view can be set on their own, in ESPRIT, MUSIC algorithm to achieve the broadband beamforming)
- 2011-06-22 13:59:34下载
- 积分：1
-
SINS
SINS matlabsimulink仿真程序
结果真实可信，附有参考文献。(SINS matlabsimulink)
- 2014-10-19 13:08:56下载
- 积分：1
-
SCIG
基于SCIG的WECS的降阶模型，以2WM，定桨距，刚性传动链的WECS为例说明降解模型及其线性化。(a reduced order model of SCIG based WECS with 2 wm, fixed pitch, rigidity of transmission chain WECS for example shows that the degradation model and its linearization.)
- 2015-01-22 16:07:51下载
- 积分：1
-
hausdorff
Matlab code for comparing two point sets
- 2012-10-23 04:08:51下载
- 积分：1
-
kalman
Overview
The Simulink model shows an example how the Kalman Filter can be
implemented in Simulink. The model itself is configured with a Gaussian
process connected with a Kalman Filter. To directly use this model, one
only needs to provide model prarameters including parameters of the
Gaussian process, which are state space matrices, A, B, C, and D, initial
state, x0, and covariance matrices, Q and R and similar parameters for
the Kalman Filter, which can be in different values to mimic the model
mismatch, plus the state covariance, P. The following examples show how
this model can be used.
The Kalman Filter can also be used as a standard model block to be
connected with any other systems
- 2016-11-13 04:05:37下载
- 积分：1
-
activeContoursSnakesDemo
本演示实现了主动轮廓模型由Kass等人提出。
要运行它的图形用户界面
1。基于MATLAB型引导提示。
2。关于“到现有的图形用户界面，点击”
3。选择在与本文件相同的目录snk.fig文件
4。按一下上方的绿色箭头启动图形界面
一旦GUI已经启动，您可以通过使用蛇
1。点击“新形象”，并加载输入图像。提供的样品图像。
2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。
3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。
4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al.
To run it with GUI
1. Type guide on the matlab prompt.
2. Click on "Go to Existing GUI"
3. Select the snk.fig file in the same directory as this file
4. Click the green arrow at the top to launch the GUI
Once the GUI has been launched, you can use snakes by
1. Click on "New Image" and load an input image. Samples image are provided.
2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image.
3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points.
4. Set the various snake paramete)
- 2010-07-05 11:54:13下载
- 积分：1
-
pls1
matlab案例，可以用于pls模型的建立(matlab case model can be used to pls)
- 2010-09-30 16:06:46下载
- 积分：1
