-
Radar_pulse_signal_detection
该程序实现了雷达信号下降沿的检测不用知道雷达脉冲信号的结束时间信噪比不可以太小(The program achieved a falling edge detection of radar signals do not know the time of the radar pulse signal the end of the signal to noise ratio can not be too small)
- 2009-12-19 19:45:47下载
- 积分：1
-
codelength_recogcompare_BCH157
里面含有盲识别BCH码的长度的代码，用于matlAB子程序调试，很好用。(BCH code which contains the length of the blind identification code for matlAB subroutine debugging, very good use.)
- 2013-11-07 16:28:35下载
- 积分：1
-
main
振动信号的预处理消除趋势项（最小二乘法消除多项式.）(Pretreatment to eliminate vibration signal Trend (least squares method to eliminate polynomial.))
- 2010-10-22 16:29:08下载
- 积分：1
-
Finite-Element-Procedures
有限元分析的源程序，包括几乎所有的求解算法和程序，直接应用 不需要二次修改。(Finite element analysis of the source code, including almost all of the solution algorithm and procedures, direct applications do not require secondary modifications.)
- 2020-12-16 22:29:12下载
- 积分：1
-
2to16
二进制转换十六进制的小程序，在控制台程序下编译成功，开发环境Visual studio 2013(Sixteen hexadecimal conversion binary)
- 2014-12-02 13:15:35下载
- 积分：1
-
matlab1
了解单频激光干涉仪的非线性误差，使用matlab软件工具对提出的非线性误差修正方法进行验证，对干涉信号中的直流分量偏差对测量的影响进行分析。(Learn nonlinearity error single frequency laser interferometer using matlab software tools for the proposed non-linear error correction method for verification of the DC component of the interference signal on the measurement of the deviation analysis.)
- 2014-11-12 22:44:26下载
- 积分：1
-
filtmatlab
filtering a signal is a very important processing in signal processing, here is some example of setting parameters and doing this process
- 2015-03-17 18:18:30下载
- 积分：1
-
04778392
Volatge balancing of Multi level converter
- 2011-12-30 23:09:44下载
- 积分：1
-
MOS_CFAR
说明： 改进的有序统计类恒虚警检测器（MOS-CFAR），适合于多目标检测(detectors based on the modified ordered statistic constant false alarm rate (MOS-CFAR) technique.)
- 2020-11-16 16:49:41下载
- 积分：1
-
基于蚁群算法的三维路径规划
说明： 用栅格模型表示工作环境,确定机器人运动起始结点和目标结点后,对工作环境进行分析,选取起始点与目标点之间连线附近的若干栅格,以被选取栅格为关键点,采用蚁群算法分别计算关键点与起始点和目标节点之间的最短路径,求取全局最短路径(With grid model to represent the working environment, robot motion after initial nodes and target, analysis of working conditions, selecting starting point and the target point near the connection between a number of grid, grid for the key points to be selected, key point and the starting point is obtained by using the ant colony algorithm respectively and the shortest path between the target node, calculate the global shortest path)
- 2020-07-03 00:02:20下载
- 积分：1
