登录
首页 » matlab » Ga1

Ga1

于 2011-04-28 发布 文件大小:4KB
0 103
下载积分: 1 下载次数: 4

代码说明:

  genetic algorithm for fetcher selection

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • FMINCON
    C=CURVEFIT( 拟合模型 ,参数C初值,X数据,Y数据) 求参数C使得 sum {(FUN(C,X数据)-Y数据).^2}最小化(C = CURVEFIT ( fitting model and parameter C, initial X, Y data) for data parameters that sum {there (C) (C, X-ray data- Y j ^ 2) minimizing})
    2010-08-16 20:23:31下载
    积分:1
  • BerMass
    The example below encodes one message words using Reed-Solomon encoder. It then corrupts the code by introducing two errors in the codeword, Then BerMass tries to the connection weight vector A and its roots R that it used to know error location.
    2012-04-24 15:32:52下载
    积分:1
  • sheildearth
    电缆模型函数的绘制程序,包括电缆屏蔽层与地之间的模型(XLPE Cable model)
    2012-10-21 08:27:29下载
    积分:1
  • PVarray_Grid_PandO_avg
    AN MATLAB DESIGN OF PV ARRAY
    2013-05-02 17:50:58下载
    积分:1
  • untitled
    matlab变压器源码单相变压器空载运行仿真(matlab source transformer single phase transformer load operation simulation)
    2020-11-04 20:59:52下载
    积分:1
  • rootfind
    计算方法 大学 求根 牛顿求根公式D:matlab mm ootfind.rar(calculation Newton University Root Root Formula D : Matlab nmm rootfind.rar)
    2006-09-06 19:04:39下载
    积分:1
  • BPSK-QPSK
    分别编写BPSK与QPSK调制解调系统的Matlab仿真程序,要求:发送滤波器与接收滤波器均为根升余弦滚降滤波器;信道噪声为加性高斯白噪声 绘制BPSK与QPSK调制下的误码率与信噪比曲线图,并与理论曲线比较对比(They were written BPSK and QPSK modulation and demodulation system Matlab simulation program requirements: a transmission filter and a reception filter are root raised cosine filter channel noise to draw error BPSK and QPSK modulation under additive white Gaussian noise rate and SNR graph, and compare and contrast the theoretical curve)
    2021-04-11 19:48:58下载
    积分:1
  • trivsr
    三相双闭环PWM整流器simulink仿真,空间矢量SVPWM,电流前馈解耦,DQ坐标变换(Double closed loop three-phase PWM rectifier, using SVPWM, current feedforward decoupling, DQ coordinate conversion, etc )
    2021-04-19 11:38:54下载
    积分:1
  • short-circuit
    这个说明倒不是说明函数的功能,只是声明一下函数中出现的问题。 shortest()函数没有问题,在secshortest中我希望只得到一条次短路(或几条roadcost()值相同的次短路),结果却出来好几条,我仔细检查了一下程序,应该没有什么问题。 因此在使用时,要得到次短路,只能用roadcost()函数分别求一下各条路的权重和,找到最小的。 有些奇怪 (Note that this is not the function of function, but a statement about the problems in function. shortest () function there is no problem, I hope that in secshortest only a short time (or several roadcost () times the value of the same short-circuit), the result is several out, I carefully examined the process, it should be no problem. Therefore, in use, to be at a short circuit can only be used roadcost () function, respectively, for some of the weight of the road and find the smallest. Some strange)
    2009-05-21 21:11:51下载
    积分:1
  • lx计算机控制
    这是我们计算机控制的一个上机题,希望大家的学习有所帮助(This is a computer-controlled machine on that, I wish you all a learning help)
    2005-06-04 11:24:19下载
    积分:1
  • 696524资源总数
  • 103938会员总数
  • 55今日下载