-
Filter_design
根据给定参数，设计相应的滤波器，实现滤波，并进行频谱分析，观察滤波效果。(In accordance to the given parameters, the design of the filter, to achieve filtering, and spectrum analyzer to observe the filtering effects.)
- 2009-05-12 11:02:01下载
- 积分：1
-
soliton
双孤子模拟程序，对光纤中的孤子进行仿真，实验结果较理想(Two-soliton simulation program, the soliton fiber simulation, more satisfactory results)
- 2011-12-20 17:48:56下载
- 积分：1
-
DLA
matlab7.0 下的一个模拟薄膜蒙特卡洛生长的DLA模型(a sample DLA model for film growth with matlab7.0)
- 2015-04-16 16:16:25下载
- 积分：1
-
activeContoursSnakesDemo
本演示实现了主动轮廓模型由Kass等人提出。
要运行它的图形用户界面
1。基于MATLAB型引导提示。
2。关于“到现有的图形用户界面，点击”
3。选择在与本文件相同的目录snk.fig文件
4。按一下上方的绿色箭头启动图形界面
一旦GUI已经启动，您可以通过使用蛇
1。点击“新形象”，并加载输入图像。提供的样品图像。
2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。
3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。
4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al.
To run it with GUI
1. Type guide on the matlab prompt.
2. Click on "Go to Existing GUI"
3. Select the snk.fig file in the same directory as this file
4. Click the green arrow at the top to launch the GUI
Once the GUI has been launched, you can use snakes by
1. Click on "New Image" and load an input image. Samples image are provided.
2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image.
3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points.
4. Set the various snake paramete)
- 2010-07-05 11:54:13下载
- 积分：1
-
T-S_module
基于T-S模型的预测控制。为Matlab文件，附有模型说明。
(TS model based predictive control. For the Matlab files, with the model description.)
- 2020-12-14 12:19:15下载
- 积分：1
-
ccfc
差分方程求解
实验步骤：
主界面下进入实验五的“差分方程求解”子系统,输入希望看到的输出样点数
输入差分方程系数向量
输入顺序为：，。其中 N+1 为差分方程两边系数最大数目，如果有一边输入系数个数小于 N+1，将按不足系数为零计算。
输入系统初始状态向量
输入顺序为
鼠标单击确定按钮，以数值和图形两种方式显示单位冲激响应和输出响应
3） 确定差分方程形式：y(k)-y(k-1)+0.35y(k-2)=2x(k)-x(k-1)，(Experimental steps for solving differential equations: the main interface into five experimental " differential equation" subsystems, would like to see the output of input sample points difference equation coefficient of input vector input sequence as follows:,. One of N+1 differential equations for the maximum number of factors on both sides, if there is one less than the number of input coefficient of N+1, the calculation will be less than zero coefficient. Initial state vector input system for the importation of the order of the mouse button to click OK to both numerical and graphical display unit impulse response and output in response to 3) to determine the form of differential equation: y (k)-y (k-1)+0.35 y (k-2) = 2x (k)-x (k-1),)
- 2009-05-01 20:35:04下载
- 积分：1
-
GraphBetweennessCentrality
一个很有用的计算网络中每个节点介数的程序，对网络分析很有用(A useful calculation of the network each node the number of referral procedures, useful for network analysis)
- 2011-07-05 23:39:47下载
- 积分：1
-
spp
银表面等离子激元SPP色散关系，参考王振林老师的《表面等离子激元的研究进展》(Silver surface plasmon dispersion relation of SPP, reference Zhenlin teacher " Surface plasmon Research Progress" )
- 2013-11-10 17:39:02下载
- 积分：1
-
Evaluation_of_Multiple_Input_Multiple_Output(MIMO
Evaluation of mimo system in wireless system
- 2014-01-24 16:35:30下载
- 积分：1
-
chamfermatching
Description of the file: template matching source of Chamfer matching algorithm. It s OpenCV implementation
- 2013-11-25 23:42:19下载
- 积分：1
