登录
首页 » matlab » jianlimoxing

jianlimoxing

于 2006-06-22 发布 文件大小:1KB
0 183
下载积分: 1 下载次数: 33

代码说明:

  基于时间序列模型的一阶滤波程序,没有解压密码,直接使用(time series model based on the filtering process an order, without extracting passwords used directly)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • PINLVJI-(2)
    1、基本要求: (1)频率测量 测量范围:1HZ~1MHZ,信号为方波、正弦波;幅度为0.1V~5V; 测量误差: 0.1 (以NFC—10A为准)。 (2)周期测量 测量范围:1HZ~1MHZ,信号为方波、正弦波;幅度为0.1V~5V; 测量误差:, 0.1 (以NFC—10A为准)。 (3)脉冲宽度测量: 测量范围:脉冲宽度不超过100μS,信号为脉冲波,幅度为0.1V~5V; 测量误差: 0.1 。 (failed to translate)
    2011-05-18 13:06:15下载
    积分:1
  • C-MAPSS-Data
    涡轮风扇发动机从正常运行至失效的全寿命采集的实验数据,对于研究涡轮风扇发动机的故障的预测及性能评估想必有用。(Turbofan engine failure from normal operation to the whole life of the experimental data collected for the study of turbofan engine failure prediction and performance evaluation must be useful.)
    2013-08-11 13:07:20下载
    积分:1
  • Alazard_2248
    Introduction Kalman filter D.Alazard
    2013-03-20 20:33:37下载
    积分:1
  • am
    说明:  amplitude modulation simulink
    2012-02-10 00:25:21下载
    积分:1
  • dipole_example_no
    对电磁波入射的源为偶极子进行仿真,可以z作为其他电磁仿真问题中的源的设置子函数用(of the incident electromagnetic wave dipole source for simulation, z#$#!264699#!#$ooutin2.rar!#$#VB and Distributed Control CD-ROM source code (digital input and output- Correction)
    2007-04-10 19:00:13下载
    积分:1
  • LBGK_D2Q9_poiseuille_channel2D
    二维泊肃叶流动的模拟源代码,利用格子波尔兹曼方法进行计算,计算结果如程序所示(The analog source code of the two-dimensional Poiseuille flow using lattice Boltzmann method is calculated, the calculated results of such procedures shown)
    2013-03-24 18:47:29下载
    积分:1
  • LPC
    利用matlab编程实现LPC谱与语音频谱的比较。( LPC spectrum using matlab programming comparison with the speech spectrum)
    2021-04-08 18:09:00下载
    积分:1
  • wind_power_in_power_systems
    研究风电接入对电力系统影响的经典书籍,适用于相关专业人士(classical text book to learn about winder power and its affect on power system)
    2012-01-19 23:36:37下载
    积分:1
  • RESORCH
    说明:  机器人同时定位与地图创建研究中重要的内容(important for SLAM)
    2010-04-08 20:00:26下载
    积分:1
  • Otsucoding
    Otsu-最大类间方差Matlab代码 最大类间方差法原理:最大类间方差法是由日本学者大津于1979年提出的,是一种自适应的阈值确定的方法,又叫大津法,简称OTSU。它是按图像的灰度特性,将图像分成背景和目标2 部分。背景和目标之间的类间方差 % 大,说明构成图像的2 部分的差别越大,当部分目标错分为背景或部分背景错分为目标都会导致2 部 % 分差别变小。(Otsu- Otsu Matlab code Otsu Principle : Otsu law by Japanese scholars in the large-1979's, is an adaptive threshold established methodology, also known as big-law, referred to Otsu. It is based on image characteristics of the gray image can be divided into the background and objectives of Part 2. Background and objectives between the between-class variance%, which meant that the two images form part of the greater difference, When some background into the wrong target or part of the background into the wrong target will lead to sub-2% difference becomes smaller.)
    2020-10-31 15:39:56下载
    积分:1
  • 696516资源总数
  • 106425会员总数
  • 12今日下载