-
mangfenli
盲源信号分离，快速高效的独立成分分析方法 希望对大家有用(Blind Source Separation, rapid and highly efficient method of independent component analysis for all of us hope that useful)
- 2009-01-03 15:20:45下载
- 积分：1
-
ofdmprogram
对低压线路的ofdm的编码与仿真程序，包括信道，编码，自适应均衡等方面(Ofdm low-voltage line coding and simulation program, including channel, coding, adaptive equalization, etc.)
- 2010-10-27 13:07:54下载
- 积分：1
-
heartbeat
heart beat monitor program for mikroC
- 2015-04-07 14:18:08下载
- 积分：1
-
Algorithm_Collections_for_Digital_Signal_Processi
Book for Algorithms Collections for DigitalSignalProcessing Applications using Matlab
- 2009-07-03 21:19:32下载
- 积分：1
-
multiuav
multi uav(多无人机matlab下的仿真)(multi uav (multi-UAV simulation matlab))
- 2021-04-25 15:18:46下载
- 积分：1
-
topoplot
说明： 脑电地形图matlab代码，可根据数值向量和通道位置文件绘制2D地形图(plot a topographic map of a scalp data field in a 2-D circular view (looking down at the top of the head) using interpolation on a fine cartesian grid.)
- 2020-12-20 19:59:09下载
- 积分：1
-
nnewmark
matlab for student and teacher
- 2011-12-08 20:21:48下载
- 积分：1
-
beamforming
固定阵列孔径，随机阵元间隔MVDR,OPT,LMS方法波束形成(Fixed array aperture, random array element interval MVDR, OPT, LMS beamforming)
- 2012-11-01 10:33:29下载
- 积分：1
-
anglecos
利用夹角余弦距离进行样本数据分类。实现步骤主要分为以下两部分：a、待测样品X与训练集里每个样品Xi的距离采用夹角余弦距离公式计算。b、循环计算待测样品和训练集中各已知样品之间的距离，找出距离待测样品最近的已知样品，该已知样品的类别就是待测样品的类别。(Using the sample data classification Angle cosine distance.Implementation steps are divided into the following two parts: a, sample under test with each of the samples in the training set X Xi distance using the included Angle cosine distance formula.B, loop calculation under test samples and the distance between the known samples training focus, find out the known closest to the sample under test samples, the samples of known category is the category of the sample under test.)
- 2015-03-30 16:27:58下载
- 积分：1
-
8QAM
利用Matlab仿真软件，完成如图1所示的一个基本的数字通信系统。信号源产生0、1等概分布的随机信号，映射到16QAM的星座图上，同时一路信号已经被分成了实部和虚部，后边的处理建立在这两路信号的基础上。实部、虚部信号分别经过平方根升余弦滤波器，再加入高斯白噪声，然后通过匹配滤波器（平方根升余弦滤波器）。最后经过采样，判决，得到0、1信号，同原信号进行比较，给出16QAM数字系统的误码。(Using Matlab simulation software, as shown in Figure 1 to complete a basic digital communications systems. Signal source such as arise over the distribution of 0,1 random signal, is mapped to 16QAM constellation diagram, at the same time all the way the signal has been divided into real and imaginary parts, behind the deal with the establishment of these two signals in the basis. Real part, imaginary part of the signal, respectively, after a square root raised cosine filter, then add white Gaussian noise, and then through the matched filter (square root raised cosine filter). Finally, after sampling, the verdict has been 0,1 signal, to compare with the original signal is given 16QAM digital system error.)
- 2007-10-22 15:57:50下载
- 积分：1
