-
linblknew.m
it is the code for linear block code
- 2009-04-06 06:19:49下载
- 积分：1
-
SVPWM
基于sinulink 的矩阵变换器控制，和PWM触发脉冲的生成(Based sinulink ' matrix converter control, and PWM trigger pulse generator)
- 2016-05-16 22:05:42下载
- 积分：1
-
dct
基于matlab编写的dct数字水印程序，文件包括有源程序以及简单的说明等(DCT matlab prepared based on digital watermarking procedures, documentation, including source code, as well as simple descriptions)
- 2008-12-19 15:56:07下载
- 积分：1
-
dypsa
algorithm for determining glottal closure instances
- 2011-05-09 10:56:56下载
- 积分：1
-
access-simulation
机动车驶入停车场对非机动车交通流的影响仿真，T_type是主程序(Vehicle into the parking lot of non-motorized transport stream simulation, T_type is the main program)
- 2012-07-07 20:37:58下载
- 积分：1
-
wangluo.m
This is a procedure for computing small-world .For large complex networks, understandably, their sheer size is very important. This procedure is useful.
- 2011-10-10 15:34:18下载
- 积分：1
-
ss-by-mf
matched filter based spectrum sinsing in cognitive radio networ
- 2013-11-20 14:50:16下载
- 积分：1
-
Simple_PIDvsGPID
经典PID与增加了高阶微分的改进PID的对比程序。(The classical PID VS the GPID with high order PID differential.)
- 2015-01-21 14:06:42下载
- 积分：1
-
chengxu
小波变换进行变速箱故障诊断
首先将s1和s2信号时域谱（s1代表维修前的振动信号，s2代表维修后的振动信号），画出来进行对比，会发现s1信号的振动幅值会比较高；然后对s1和s2分别进行小波分解并画出各层的时域谱，只对比s1和s2分后的最高时域谱，s2更加的具有周期性，且幅值较小，s2周期性不够明显，且振动过于密集。分析完时域谱后开始分析频谱，首先对原信号s1和s2fft转换，得到频谱图，如图，然后再对小波分析后高频部分进行fft转换，做出频谱图。对比后我们发现，在f 2375HZ出（也就是齿轮的啮合频率），s1信号频谱幅值会有急剧的升高，然后，其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)
- 2017-01-17 19:18:02下载
- 积分：1
-
FMCW-Radar-Simulator-master
说明： 1） 这是一个基于MATLAB的FMCW射频雷达模拟器。
2） 它产生FMCW雷达，用于近距离的手波啁啾电平信号数据。
3） 你可以尝试在这个模拟器上开发你的雷达数据处理算法。
4） 作为一个查伦奇，你能开发你的算法来检测手写方向：左或右。
5） 在matlab中运行main.m开始尝试。(1) This is a MATLAB based FMCW RF Radar Simulator.
2) It generates FMCW radar for close handwave chirp level signal data.
3) Your can try develop your radar data processing algorithm base on this simulator.
4) As a charllenge, can you develope your algorithm to detect the handwave directions: LEFT or RIGHT.
5) Run main.m in matlab to start trying out.)
- 2020-03-18 10:22:43下载
- 积分：1
