-
基于LabVIEW的通用自动测试系统设计
说明： 基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
VirtualOscilloscope
说明： 虚拟示波器的设计， 基于LabVIEW的虚拟示波器设计 (Virtual Oscilloscope)
- 2021-04-13 19:58:56下载
- 积分：1
-
Singal-process-for-spindle-
对采集的主轴两向位移信号进行处理，得到轴心轨迹图(The two axis displacement signal of the spindle is processed to obtain the axis orbit )
- 2017-05-03 09:37:39下载
- 积分：1
-
LABVIEW_TONGBU
LABVIEW prepared by the NI timing synchronization control card, control the camera synchronized shooting
- 2016-12-27 12:52:15下载
- 积分：1
-
generate pwm
说明： 用户自行输入所需要的频率和占空比，得到PWM波(Users input the required frequency and duty cycle to get the PWM wave.)
- 2020-06-17 01:40:01下载
- 积分：1
-
UsingTheProgramToGenerateAtriggerEvent
labview中用程序去产生一个触发事件是个难点，相关的介绍和例子并不多，本程序使用值属性信号结点改变的方法去产生一个事件，实现程序控制产生触发事件的功能，labview开发版本8.2。(labview using the program to generate a trigger event is difficult, relevant examples of the introduction are not many,here we use the value change of the node attribute of the signal to generate an event, the realized the program control functions to generate trigger events, the version of labview development is 8.2 .)
- 2009-04-15 02:58:25下载
- 积分：1
-
labview串口的队列接收方式 ComQueue
labview串口的队列接收方式，有效解决labview串口接收时字节错乱问题(labview visa queue send and receive)
- 2020-07-02 23:00:01下载
- 积分：1
-
自制控件
如何制作LabView控件，赖卫国整理，方便可行(How to make labview control, Lai Weiguo collation, convenient and feasible)
- 2019-06-12 15:24:11下载
- 积分：1
-
measure-AM-and-power-spectrum
用于测量信号的振幅谱与功率谱，对初学LABVIEW做信号分析会有帮助。(Used to measure the signal amplitude spectrum and the power spectrum, signal analysis for beginners LABVIEW do help.)
- 2014-10-18 16:38:14下载
- 积分：1
-
AQUIR
对信号进行采集和保存，其采样率默认为信号频率的10倍，并将采集到的信号数据保存到电子表格中(Save signal data acquisition and preservation of the signal, the default sampling rate is 10 times the signal frequency, and collected into a spreadsheet)
- 2014-02-16 13:57:44下载
- 积分：1
