-
fdct_wrapping_matlab
采用中心旋转法来进行曲波变换，带有几个demos。方便的进行curvelet变换(Center of rotation method used to carry out curvelet transform, with a few demos. Convenient for curvelet transform)
- 2010-06-10 18:51:18下载
- 积分：1
-
calculangle
fonction pour calculer angle
- 2009-10-02 18:02:09下载
- 积分：1
-
RSSs_sIV_v2
RSS mesurement in sensor network
- 2010-12-20 01:27:51下载
- 积分：1
-
DIANMUBIAOHUIBO
雷达点目标成像：产生Stripmap SAR的回波 (Radar point target imaging)
- 2013-03-27 20:00:58下载
- 积分：1
-
xitongbianshi
系统辨识基于梯度校正的参数辨识方法，其中包括随机牛顿法，确定性梯度下降法(System identification based on the gradient correction parameter identification methods, including random Newton' s method, deterministic gradient descent)
- 2011-11-18 09:43:43下载
- 积分：1
-
cyclic2_am
AM信号的循环谱的matlab代码实现，初学者适合 (The AM signal of the cyclic spectrum of matlab code, suitable for beginners
)
- 2013-10-25 12:05:27下载
- 积分：1
-
自适应滤波器的最陡下降法示意图-fig811
自适应滤波器的最陡下降法示意图(adaptive filter steep decline in the most schematic)
- 2005-02-17 15:55:08下载
- 积分：1
-
sift
提取图像sift特征，并且showkey函数在图像上直观的显示出来(Sift extracted image features, and showkey function in the image displayed on the intuitive)
- 2010-11-09 10:41:09下载
- 积分：1
-
db_nc_audio_recon
说明： 使用5阶巴特沃斯半带滤波器4通道完美重构滤波器组来处理音频数据的例子(Using the 5-order Butterworth filter with a 4-channel semi-perfect reconstruction filter banks to process audio data examples)
- 2010-05-04 01:19:54下载
- 积分：1
-
pulse-generate
本程序是矩形波的产生。第零步定义了要产生的波形的所有特征参数，矩形波的持续时间WIDTH，矩形波的采样点数POINTS,载波频率为F0，这个频率的最终引入是便于使用RF频率发射波形。第一步包括产生矩形波，并将其调制到RF上，注意，产生的信号的持续时间是矩形波宽度的5倍，这样，总的采样点数就是5*POINTS。同时还应注意，如果要产生一个基带信号，必须设置T0=0.第二步是画出所产生矩形波的源代码。( This procedure is rectangle wave production. Step to produce stage defined the waveform of all characteristic parameters, the duration of the rectangle wave WIDTH, rectangle wave sampling POINTS POINTS, carrier frequency F0, this frequency for the ultimate introduction is easy to use RF frequency emission waveforms. The first step including generating rectangle wave, and modulated to RF, attention, produce the duration of the signal is five times the width of rectangle wave, so, overall sampling POINTS is 5* POINTS. Also, note that if you want to produce a baseband signals must set T0 = 0. The second step is to draw a rectangular wave generated by the source code. )
- 2011-05-21 10:52:01下载
- 积分：1
