-
kaiguandianyuan
Buck变换器是最常用的变换器,工程上常用的拓扑如正激、半桥、全桥、推挽等也属于Buck族,其中Buck变换器补偿网络设计,是开关电源的重要研究课题,本文将针对基于PI控制方式的4A开关电源进行设计和Multisim的仿真研究。(Buck converter is the most commonly used converter on the topology of the project, such as forward, half bridge, full bridge, push-pull, the Buck family, Buck Converter compensation network design is an important research topic of the switching power supply, this paper4A-based PI control switching power supply design and Multisim simulation study)
- 2012-03-11 08:54:50下载
- 积分:1
-
psnr
计算峰值信噪比,可以用于检查图像密写的效果(Calculation of peak signal to noise ratio, images can be used to check the effect of Steganography)
- 2009-05-05 17:45:02下载
- 积分:1
-
FOG_test
一个计算光纤陀螺速率斜坡系数、速率随机游走系数、零偏稳定性、角度随机游走系数、量化噪声系数的matlab程序(A calculation of the slope coefficient of fiber optic gyro rate, rate random walk coefficient, bias stability, angle random walk coefficient quantization noise figure of the matlab program)
- 2011-10-06 16:37:58下载
- 积分:1
-
matlabliness
文档介绍利用matlab进行非线性曲线拟合时的例子以及所需函数(The document describes the non-linear curve fitting using matlab example, and the desired function)
- 2012-11-20 15:31:38下载
- 积分:1
-
self-tuning-control
广义最小方差自校正控制:在求解控制律的性能指标中引入对控制量的加权项,限制控制作用中的剧烈变化。(Generalized minimum variance self-tuning control: control the amount of weighted items, solving the performance of the control law introduced to limit the dramatic changes in the control action.)
- 2012-10-09 17:43:11下载
- 积分:1
-
hilberttest
此例程可以用来进行希尔伯特变换,得到包络谱,利用差分公式得到瞬时频率(This routine can be used to carry out Hilbert transform, obtain envelope spectrum, and obtain instantaneous frequency by using difference formula)
- 2018-10-13 19:15:39下载
- 积分:1
-
Trace-point-of-attachment
在直角坐标中描出不同的坐标,然后连成线,在matlab中显示。(Trace different coordinates in the rectangular coordinates, and then connect line, shown in matlab.
)
- 2013-04-10 19:55:46下载
- 积分:1
-
_Rudolf._Lidl__H
Book on Information theory and its various applications.
- 2015-04-06 13:55:43下载
- 积分:1
-
PC-CFR
采用matlab simulink编写的消峰参考设计,可以直接生成verilog代码。消峰主要用于降低无线信号的峰均比,提高功放效率。(Clipping prepared using matlab simulink reference design, you can generate verilog code directly. Consumers peak mainly used to reduce radio signal PAR, improve power amplifier efficiency.)
- 2020-12-16 17:09:12下载
- 积分:1
-
matlab2
这本书是关于matlab文件操作和txt等文件转换的资料,希望对大家有用,有好的资料也请大家上传上来 谢谢~(err)
- 2008-01-05 11:03:38下载
- 积分:1