登录
首页 » matlab » Information-hiding

Information-hiding

于 2021-04-06 发布 文件大小:10495KB
0 137
下载积分: 1 下载次数: 53

代码说明:

  基于 DCT(离散余弦变换 )域的信息隐藏算法是目前应用最广的变换域算法 ,此类算法的最大不足是嵌信息量小。通过分析 DCT域隐藏算法隐藏容量少的原因 ,提出了一种大容量的 DCT域信息隐藏算法。算法首先对载体图像进行频谱均匀化处理 ,然后对图像进行全局 DCT变换 ,并将隐藏信息嵌入到载体图像的低频 DCT系数上 ,信息嵌入采用分段量化的方法实现 ,提取隐藏信息时不需要原始载体图像。实验结果表明 ,该算法的嵌入容量大 ,不可感知性好。(Based on DCT (discrete cosine transform) domain information hiding algorithm is the most widely used transform domain algorithms, the largest of these algorithms is the lack of a small amount of information embedded. Hiding Algorithm for DCT domain by analyzing the hidden reasons for the low capacity, a large capacity of information hiding algorithm for DCT domain. Firstly, the spectrum of the carrier image homogenization, and then the image is a global DCT transformation, and hidden information embedded into the image of the low-frequency DCT coefficients, the information embedded in the methods used to achieve sub-quantization, extract hidden information without the original Vector image. Experimental results show that the algorithm embedding capacity, can not be perceived good.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • matlabjuanji
    在matlab 环境下运用卷积算法实现对图像损坏区域的修复。(Matlab environment in the use of the image deconvolution algorithm to repair damage to the region.)
    2009-04-10 13:13:02下载
    积分:1
  • pc_cfr_v2_0_msim_r2_0
    Xilinx公司pc_cfr IP核的MatLab仿真(matlab simulation model of pc_cfr ip core of xilinx)
    2010-11-25 09:20:29下载
    积分:1
  • svdnew
    PMSM直接转矩控制系统的空间辨识,辨识出系统介次,和状态空间模型,从而调节控制器参数(PMSM Direct Torque Control System Identification, identify system Kaiji, and the state-space model, adjust the controller parameters)
    2006-12-09 20:05:56下载
    积分:1
  • mds
    多维标度变换是应用广泛的无线传感器网络定位算法(Multi-Dimensional Scaling)
    2013-08-18 18:22:51下载
    积分:1
  • Lungelo-DOL
    A simulink model for a direct online starting of an induction motor connected directly across the line.
    2013-08-15 23:46:55下载
    积分:1
  • QAMbianma
    QAM的matlab编码,可以看QAM的一定信噪比下,信号的误码率情况(The encode of QAM use MATLAB)
    2010-12-03 11:43:39下载
    积分:1
  • JPGcoder
    Decoding Jpeg image in matlab programm
    2015-01-22 02:40:34下载
    积分:1
  • MySpectrum1
    本程序是计算振动信号各种参数的实验程序。 主要功能是计算均值、标准差、方差、偏斜度、峭度、 峰峰值、方根幅值、平均幅值、峰值、 波形指标、峰值指标、脉冲指标、裕度指标。 (matlab index)
    2017-01-07 11:12:18下载
    积分:1
  • exam
    智能信息处理应用的实例,有模糊推理及其仿真(Intelligent Information Processing Examples of applications, has fuzzy inference and simulation)
    2007-09-12 13:14:21下载
    积分:1
  • system-simulation-of-RFID
    对RFID系统在MATLAB中进行仿真,并提出了方案,和重要的结果。(A simulation in MATLAB/simulink. It not only provides details about how to realize RFID system, but also shows the final result of this system.)
    2011-04-22 14:37:16下载
    积分:1
  • 696518资源总数
  • 105877会员总数
  • 14今日下载