-
STM32F103RBT6PLC
stm32f103rbt6 plc fx1n
- 2019-07-08 17:13:12下载
- 积分：1
-
hw-master-v1.0.6
foxBMS开发代码，德国的开源BMS开发共享平台，GITHUB搬运(foxBMS code, from foxBMS in Germany, which is open source on Github)
- 2018-11-22 17:18:18下载
- 积分：1
-
CMT2300A_DemoEasy_v1.1
泽太微电子（CMOSTEK）的CMT2300A驱动参考代码(Sample Code for CMT2300A)
- 2017-09-08 17:41:02下载
- 积分：1
-
test_1
使用atmega128芯片完成单片机的流水灯设置，并能灵活修改代码完成个人所需。(Complete water lights singlechip set using the ATmega128 chip, and can easily modify the code to complete the personal needs.)
- 2013-03-10 16:30:03下载
- 积分：1
-
hi3521a-datasheet.tar
Hi3521A V100 H.264 CODEC Processor Brief Data Sheet.pdf
Hi3521A-Hi3520DV300 H.264 CODEC Processor Data Sheet.pdf
- 2018-04-04 16:46:26下载
- 积分：1
-
多功能测量(功能)
说明： 温度，光照强度，测距，检测lcd1602显示，上传串口显示(Temperature, illumination intensity, ranging, detection LCD1602 display, upload serial display)
- 2020-06-18 23:40:02下载
- 积分：1
-
1_2_led_systick
应用LPC1788 sys时钟控制led，实现led秒闪烁，开发板上试验成功(Using LPC1788 sys clock to control LED, led seconds flicker is achieved, and the test is successful on the development board.)
- 2018-05-04 15:09:53下载
- 积分：1
-
UART
基于FS44B0X arm开发板的UART演示程序包含IO初始化，UART通讯测试
(FS44B0X arm development board based demo program contains IO initialize UART, UART communications test)
- 2011-05-19 10:33:30下载
- 积分：1
-
Lcd
ILI9341 stm32 fsmc 16bit
- 2015-09-06 11:51:08下载
- 积分：1
-
AVR230_source
This is a simple bootloader for AT91SAM7 processors. It
permits you to download new code to the device over USB. This bootrom is
installed at address 0x00000000 in the ARM, which means that it is the
first piece of code to execute after reset. At startup, it waits for
a few seconds to see if the downloader is trying to connect. If not,
then the bootloader gives up control and jumps to your program. If the
downloader is trying to connect, then the bootloader receives the new
program over USB and writes it into flash.(This is a simple bootloader for AT91SAM7{S,X}{64,128,256} processors. It
permits you to download new code to the device over USB. This bootrom is
installed at address 0x00000000 in the ARM, which means that it is the
first piece of code to execute after reset. At startup, it waits for
a few seconds to see if the downloader is trying to connect. If not,
then the bootloader gives up control and jumps to your program. If the
downloader is trying to connect, then the bootloader receives the new
program over USB and writes it into flash.)
- 2009-11-17 10:47:55下载
- 积分：1
