-
CH5
This is a GUI based system. The GUI is invoked from the command line by typing "ui_start". The GUI is self explanatory.
Tool tips are given in blue color. The cursor needs to be positioned on these for detailed explanation. The main file is
"runsim.m".It is recommended that 10000 runs (packets) be used for plotting frame error rates and 5000 runs for BER/SER.
Obviously, you would require a fast machine!!! At least a P4 machine.
We have used trace criterion for 4PSK states 4,8 and 16 as an example for 2x2 cases. The reader can use rank and determinant
criteria, by commenting the trace criterion lines and copying the rank and determinant lines from the respective 2x1 cases.
The SNR range can be varied by correcting the range at line 36 of file "runsim.m".
This software has been tested with MATLAB version 6.0 and above with signal processing and communications toolbox options.
(This is a GUI based system. The GUI is invoked from the command line by typing " ui_start" . The GUI is self explanatory. Tool tips are given in blue color. The cursor needs to be positioned on these for detailed explanation. The main file is " runsim.m" . It is recommended that 10000 runs (packets) be used for plotting frame error rates and 5000 runs for BER/SER. Obviously, you would require a fast machine!!! At least a P4 machine. We have used trace criterion for 4PSK states 4,8 and 16 as an example for 2x2 cases. The reader can use rank and determinant criteria, by commenting the trace criterion lines and copying the rank and determinant lines from the respective 2x1 cases. The SNR range can be varied by correcting the range at line 36 of file " runsim.m" . This software has been tested with MATLAB version 6.0 and above with signal processing and communications toolbox options.)
- 2011-05-04 09:22:01下载
- 积分：1
-
MELCEPST
MATLAB下计算Mel倒谱的函数，在语音特征提取方面常用(Mel cepstrum calculated under MATLAB functions used in the speech feature extraction)
- 2010-05-31 14:24:38下载
- 积分：1
-
allen
在MATLAB中实现地球两点的的计算,可以方便的得出方位,仰角,距离(in MATLAB 2:00 of the Earth's calculation, can easily come to the position, elevation, distance)
- 2007-05-17 10:59:53下载
- 积分：1
-
shyz
小波分析的matlab程序基于MATLAB的系统分析与设计－小波分析(The wavelet analysis matlab program analysis system based on wavelet analysis and design of MATLAB)
- 2014-11-28 20:01:19下载
- 积分：1
-
read_letter
reading of lettrrs on page
- 2011-06-17 04:54:01下载
- 积分：1
-
trns
The model used for creating the reference voltage is shown
in Fig. 4. First, photovoltaic output current (Ipv) and output
voltage (Vpv) are passed through a first order low pass filter
with a magnitude of G = 1 and a time constant of T = 0.01
seconds in order to filter out the high frequency components
or harmonics from these signals as shown in Fig. 5 and Fig. 6.
The filtered current and voltage signals (Ipv_F and Vpv_F) are
then fed into the MPPT control block that uses the Incremental
Conductance Tracking Algorithm. An algorithm that is based
on the fact the slope of the PV array power curve shown in
Fig. 7 is zero at the Maximum Power Point (MPP), positive on
the left of the MPP, and negative on the right. The MPP can
thus be tracked by comparing the instantaneous conductance
(I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
- 2013-07-23 17:45:44下载
- 积分：1
-
morelli
该段程序描述了如何去估计多普勒频率变化率。参考文献为Morelli的《Doppler-rate estimation for digital burst transmission》( This section describes how to program the estimated Doppler frequency rate of change. References to Morelli s "Doppler-rate estimation for digital burst transmission")
- 2020-08-14 14:58:36下载
- 积分：1
-
errperf
matlab program to calculate error performance
- 2011-02-06 00:21:57下载
- 积分：1
-
RPCA
主成分分析法将图像分为低秩部分和稀疏部分(Principal Component Analysis (PCA) divides images into low rank and sparse parts)
- 2019-02-15 14:50:45下载
- 积分：1
-
CMU-CS
卡内基梅隆大学的信号处理算法Matlab代码，包括ICA、PCA等(Carnegie Mellon University, Matlab code of signal processing algorithms including ICA, PCA, etc.)
- 2010-08-10 21:53:30下载
- 积分：1
