-
tsai
matlab下的两步法标定程序,应该对大家有所帮助(matlab under the two-step calibration process should be helpful to everyone)
- 2007-10-15 12:14:26下载
- 积分:1
-
yichuansuanfayouhua
遗传优化算法优化权值与阈值,视神经网络训练次数减少(Genetic optimization algorithm to optimize the weights and threshold, optic nerve network fewer training
)
- 2012-04-04 16:24:31下载
- 积分:1
-
mocvd
这是计算光子晶体程序,对研究光子晶体的同行很有用(This is the calculation procedures for photonic crystals, photonic crystals to study the usefulness of the peer)
- 2009-03-28 09:44:59下载
- 积分:1
-
Proficient-in-MATLAB-GUI-design
精通MATLAB GUI设计,第2版,电子工业出版社(Proficient in MATLAB GUI design,2nd edition, Electronic Industry Press)
- 2015-03-12 13:50:25下载
- 积分:1
-
cmablinde
信号处理的码件间干扰的解决问题方法,用盲均衡方法解决问题(Signal processing code pieces to solve the problem of intersymbol interference method, the solution to the problem of blind equalization)
- 2007-11-12 16:35:41下载
- 积分:1
-
IIR-
低通IIR数字滤波器设计,用数字滤波器的单位脉冲响应序列h(n)模仿模拟滤波器的冲激响应ha(t),令 h(n)=ha(nT),其中T为采样间隔。将模拟滤波器转换成数字滤波器的实质是,用一种从s平面到z平面的映射函数将Ha(s)转换成H(z)。数字滤波器的频率响应模仿模拟滤波器的频响,s平面的虚轴映射z平面的单位圆,相应的频率之间成线性关系。(Low-pass IIR digital filter design)
- 2011-05-03 10:02:37下载
- 积分:1
-
1
说明: 模糊控制实例说明,请大家下载观看哦,希望对你们有用(Fuzzy control examples, please download watch Oh, I hope useful)
- 2013-07-17 13:05:45下载
- 积分:1
-
tongjiguochengjianzhi
:在介绍过程监控主要内容及方法的基础上,归纳分析了统计过程监控的发展,详细阐述了传统
的PCA、PCR、PLS、FDA、HMM 和几种改进的PCA方法.指出,将人的经验和专家知识融人到PCA统计过程
监控,提高PCA的故障检测、隔离能力,完善故障诊断与评价能力,将是一个有价值的研究方向(: In the introduction the main content and methods of process monitoring based on the inductive analysis of the statistical process monitoring of development, elaborated on the traditional PCA, PCR, PLS, FDA, HMM, and several improved PCA method. Pointed out that the human experience and financial expertise to the PCA statistical process monitoring of people and improve the PCA fault detection, isolation, and improve fault diagnosis and evaluation capacity, will be a valuable research)
- 2011-05-16 10:27:55下载
- 积分:1
-
TheFilterDesign
使用matlab编写的图像滤波器,带gui(Written in the image filter using matlab with gui)
- 2011-10-23 10:07:14下载
- 积分:1
-
gnss-sdr-master
In order to start using GNSS-SDR, you may want to populate ```gnss-sdr/data``` folder (or anywhere else on your system) with raw data files. By raw data we mean the output of a Radio Frequency front-end s Analog-to-Digital converter. GNSS-SDR needs signal samples already in baseband or in passband, at a suitable intemediate frequency (on the order of MHz). Prepare your configuration file, and then you are ready for running ```gnss-sdr config_file=your_configuration.conf```, and seeing how the file is processed.
- 2015-02-12 22:57:51下载
- 积分:1