-
trainingwithequalizer
this code for add training sequence in OFDM system
- 2014-12-15 04:41:43下载
- 积分：1
-
smith_chart
define the plot area with Smithchart using matlab
- 2015-01-21 16:00:25下载
- 积分：1
-
Coverage
This code file will start STK 11.0 software and calculate the coverage of a desired region.
it will be very useful to space engineers.
- 2016-12-22 19:55:10下载
- 积分：1
-
LQR
说明： LQR最优控制，可以应用于基于磁流变阻尼器汽车悬架等半主动控制(LQR optimal control can be applied to semi-active control of vehicle suspension based on MR damper.)
- 2021-03-03 10:49:33下载
- 积分：1
-
MATLAB 2002 MDP
说明： 利用马尔可夫决策过程求解动态规划问题，希望对大家有所帮助了(Using Markov Decision Process to Solve Dynamic Programming Problem, I hope it will be helpful to all of you.)
- 2019-06-24 15:43:22下载
- 积分：1
-
ml
说明： OFDM的最大似然同步算法的MATLAB程序(Maximum Likelihood OFDM synchronization algorithm MATLAB program)
- 2008-05-19 18:53:23下载
- 积分：1
-
edgeofSAR
几篇关于SAR图像边缘检测的论文，包含各种边缘检测算法的比较，可以统一下载来对比使用，看各种方法优缺点。(SAR image edge detection on several papers, including the comparison of various edge detection algorithms can be downloaded to compare the use of uniform, to see advantages and disadvantages of various methods.)
- 2011-05-29 12:57:01下载
- 积分：1
-
Tutorial-on-Onset-Detection
音乐起始点的检测，声音处理专家Bello教授的paper(Detection, sound processing expert Professor Bello music starting point paper)
- 2014-11-14 12:48:54下载
- 积分：1
-
IMU
惯性测量单元的C源代码 用于测量物体的姿态变化 可应用与惯性导航 小飞机等设计(IMU(inertial measurement unit) source code)
- 2014-02-20 16:05:33下载
- 积分：1
-
grd_test
xwch_test.m是主测试文件；biaoji.mat存放滤波器系数；xiangweicha.m用FFT计算相位差。
仿真框架为：
1.标记信号和双音信号续接作为发送信号；
2.对双音中一个频率分量的相位做偏移，再经过一个低通滤波器（引入线性相位，模拟收发不能同步测量现象）后，作为收到的信号；
3.用一个检测信号对收发信号进行相关运算；
4.画出收发信号以及相关处理后的信号。找出相关信号的那个尖点，从而推算出收发双音信号0相位点；
5. 输入0相位点位置，计算相对相位差。(xwch_test.m is the main test file biaoji.mat store filter coefficients xiangweicha.m calculated using FFT phase difference. Simulation framework: 1. Mark signals and then as a two-tone signal continued to send signals 2. On a two-tone frequency components of the phase shift to do, and then through a low pass filter (the introduction of linear phase, simulation can not simultaneously send and receive measuring the phenomenon), the as received signal 3. using a detection signal of the transceiver signal correlation operation 4. draw send and receive signals and related processed signal. Correlated signal of the cusp, which calculate the two-tone signal transceiver 0 phase point 5. Enter 0 phase point position, calculate the relative phase difference.)
- 2010-06-12 17:31:00下载
- 积分：1
