-
xian
运用matlab软件，编程运算，进行回归分析(Use matlab software, programming operations, the regression analysis)
- 2013-09-14 10:15:19下载
- 积分：1
-
2fsk
2FSK频率选择法调制及相关检测、包络检测的matlab程序，供仿真参考(2FSK modulation frequency selection method and related testing, envelope detection matlab program for the simulation of reference)
- 2013-10-29 20:14:44下载
- 积分：1
-
EXPONENTIAL
making exponential signal with matlab
In communications, the purpose of using exponential signals instead of sinosuid ones is to use both halves of signal spectrum(Negative and Positive sides of spectrum).
For example an FSK signal can not simply downconverted to DC. because its spectrum is not symmetric around its center frequency, so you should downconvert it with exponential signal( the idea of using I and Q downconverter).
- 2013-05-25 01:05:06下载
- 积分：1
-
lyapunov
说明： MATLAB求解最大lyapunov指数源代码(MATLAB to solve the largest index of the source code lyapunov)
- 2009-08-18 15:49:25下载
- 积分：1
-
Pccard
通过PCCARD SPEC测试笔记本的外部接口的电压是正常(through PCCARD SPEC test notebook external interface voltage is normal)
- 2007-03-05 17:08:36下载
- 积分：1
-
Design-of-a-Nonlinear-PID-Neural-Trajectory-Track
Design of a Nonlinear PID Neural Trajectory Tracking
Controller for Mobile Robot based on
Optimization Algorithm
- 2015-01-06 03:40:53下载
- 积分：1
-
FuzzyPID
说明： 里面有三个二维模糊调节器分别实现PID控制器的参数Kp，ki，Kd，的调节。其控制原理：根据前面的偏差e和偏差变化ec将三个模糊控制器FC1,FC2,FC3分别进行模糊化，模糊逻辑推理，解模糊化。最后得到pid控制器参数调节量。(There are three two-dimensional fuzzy controller to achieve PID controller parameters were Kp, ki, Kd, of the regulation. The control principle: According to the previous error e and error change ec the three fuzzy controller FC1, FC2, FC3 were fuzzy, fuzzy logic, defuzzification. Finally, adjust the controller parameters by pid.)
- 2010-04-28 23:53:42下载
- 积分：1
-
SINS-Alignment(matlab)
捷联惯导初始对准的程序 matlab写的 包括动基座和静基座对准。(Initial Alignment of SINS program written in matlab, including dynamic and static alignment.)
- 2011-05-30 16:29:25下载
- 积分：1
-
M3-Files
有限单元集成刚度程序，用于计算常见单元刚度矩阵及集成。(beamassemble .ect.)
- 2010-07-23 16:51:32下载
- 积分：1
-
S200502106_SVM_for_classfication
说明： SVM用于模式识别
整理别人的代码（原来的是英文）所得：
kernel.m用于内积矩阵的计算
svcplot.m用于绘图
svm168.m是主程序
testlin.m是采用线形内积函数的支持向量机应用的 文件
testrbf.m是采用RBF内积函数的支持向量机应用 的 文件
每个文件中都有说明。
仿真平台matlab7.0, 仿真全部通过
将所有文件拷贝到work目录下（注意不要直接将上层文件夹直接拷贝到work目录下，若那样操作，必须在matlab的file菜单中的set path中设置相应的路径）。
打开matlab，在命令窗口中输入 testlin或testrbf 即可查看结果。
(SVM pattern recognition for collating other people's code (the original is in English) from : kernel.m plot within the matrix for the calculation svcplot.m for graphics is the main svm168.m testlin.m procedure is used linear plot function within the SVM application documents testrbf.m RBF is using plot function within the SVM applications each file documents were described. Matlab7.0 simulation platform, all through the simulation of all the documents copied to the work directory (not directly to the attention of the upper folder directly copied to w contex directory, as if the operation, Matlab in the file menu on the set path corresponding set the path). Open Matlab, in the command window or imported testlin testrbf can see the results.)
- 2020-12-08 16:59:21下载
- 积分：1
