登录
首页 » Visual C++ » 2DFT

2DFT

于 2012-05-27 发布 文件大小:7KB
0 185
下载积分: 1 下载次数: 39

代码说明:

  以上是二维傅里叶变换程序源代码 还有傅里叶反变换(These are the two-dimensional Fourier Transform source code for inverse Fourier transform)

文件列表:

傅里叶变换与反变换程序.doc,35328,2012-05-16

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • GPIO
    this program for student. toturial for gpio stm
    2013-04-21 00:09:38下载
    积分:1
  • STM8-MCU
    STM8 源代码 STM8 programming language TMIR1 TMIR2 SPI IIC (STM8 programming language TMIR1 TMIR2 SPI IIC )
    2012-05-07 17:25:37下载
    积分:1
  • chuanxing-da
    串行da模块的应用,和单片机通信,通过单片机控制da模块(Serial da module application, and single-chip communication, via da MCU control module)
    2013-07-18 02:57:14下载
    积分:1
  • pmsg
    很好的一个永磁同步电机的控制仿真模型,自己的参考。(Good control of a permanent magnet synchronous motor simulation model of their own reference.)
    2014-08-31 15:37:38下载
    积分:1
  • AD7991Test
    ad7991测试程序,需要自己填写控制字(ad7991 testing procedures need to fill their own control word)
    2016-02-27 21:41:50下载
    积分:1
  • ovl30u_vp1
    此程序用于adina粘塑性材料的二次开发,仅仅针对二维。( This procedure is used for the two development of ADINA viscoplastic materials, only for two-dimensional. )
    2016-08-11 21:28:52下载
    积分:1
  • 按键 步进电
    步进电机是将电脉冲信号转变为角位移或线位移的开环控制电机,是现代数字程序控制系统中的主要执行元件,应用极为广泛。。在非超载的情况下,电机的转速、停止的位置只取决于脉冲信号的频率和脉冲数,而不受负载变化的影响,当步进驱动器接收到一个脉冲信号,它就驱动步进电机按设定的方向转动一个固定的角度,称为“步距角”,它的旋转是以固定的角度一步一步运行的。可以通过控制脉冲个数来控制角位移量,从而达到准确定位的目的;同时可以通过控制脉冲频率来控制电机转动的速度和加速度,从而达到调速的目的。(Stepper motor is an open loop control motor which transforms electrical pulse signal into angular displacement or linear displacement. It is the main executive element in modern digital control system, and is widely applied. In the case of non overloaded, the motor speed and stop position depends only on the pulse frequency and pulse number, regardless of load changes, when the stepper driver receives a pulse signal, it drives stepper motor to set the direction of rotation of a fixed angle, called "step", it is the rotation of the fixed point of the operation step by step. We can control the angular displacement by controlling the number of pulses, so as to achieve the goal of accurate positioning. At the same time, we can control the speed and acceleration of motor rotation by controlling the pulse frequency, so as to achieve the purpose of speed regulation.)
    2018-01-29 13:24:17下载
    积分:1
  • STM8-C-language-programming
    STM8 C language programming
    2016-07-19 11:28:52下载
    积分:1
  • debye5(1)
    说明:  由晶格振动声子态密度计算迪拜温度、比热、振动熵等热力学性质的程序。(the programme for caculation of the debye temprature,specific heat, entropy and so on from the DOS of phonon )
    2011-04-18 15:09:14下载
    积分:1
  • EEPROM
    本系统是基于mega16的EEPROM的读写,程序可靠!(The system is based on the mega16 the EEPROM read and write, program and reliable!)
    2011-07-08 18:14:03下载
    积分:1
  • 696518资源总数
  • 105547会员总数
  • 4今日下载