-
RCPCED
仿真程序主体部分由c语言完成,改变运行的设定的参数，在相同的信道编码速率下，通过改变误码率，用Matlab软件进行画图，得出在相同编码速率不同误码率下的纠错后误码的比率，接着改变编码速率，重新可以划出另外的两条曲线；(simulation program from the main part of the completion c language, change the operation of the set parameters, the same channel coding rate, by changing the error rate using Matlab software for drawing, reached the same rate of different coding error rate after correction of the error rate, and then change the coding rate, can be re-drawn the other two curves;)
- 2007-05-09 08:50:00下载
- 积分：1
-
filt
Sample MATLAB code for FIR filter
- 2014-12-07 21:31:01下载
- 积分：1
-
Buck基础电路仿真+PID控制电路原理图
Buck基础电路MATLAB的Simulink仿真，12V-5V，参数已经调好 PID控制Buck电路原理图（VISIO图）(Simulink simulation of Buck basic circuit MATLAB, 12V-5V, parameters have been adjusted PID control Buck circuit schematic (VISIO diagram))
- 2020-11-23 17:09:34下载
- 积分：1
-
Simulation_Code
导航卫星粗糙面前向散射建模，应用基尔霍夫近似法求解(Navigation Satellite rough in front of the scattering modeling)
- 2014-04-23 16:48:55下载
- 积分：1
-
枝切法和质量图法相位解缠
说明： 利用枝切法和质量图法引导相位解缠，可用于InSAR数据处理(Phase unwrapping guided by branch-cut method and mass graph method)
- 2019-03-29 20:27:28下载
- 积分：1
-
icicancellation
this about the ici cancellation technique for ofdm
- 2009-10-24 17:58:29下载
- 积分：1
-
JA_IA_for_an_unstructured_Mesh
Finding JA IA for an unstructured Mesh
- 2014-11-26 15:50:51下载
- 积分：1
-
30-p1795-114191
基于二阶泛模型的无模型自适应控制及参数整定，充分利用无模型自适应控制边建模边控制的特点，推导基于二阶泛模型的改进无模型自适应控制，应用辨识出的近似模型针对不同目标函数进行优化(Pan model based on second order approximation model of model-free adaptive control and parameter tuning, make full use of model-free adaptive control side edge control modeling features derived model-free adaptive control model based on improved second-order pan, identify the application The objective function to be optimized for different)
- 2014-07-15 21:38:59下载
- 积分：1
-
PerceptronRecognition
模式识别，感知器训练算法Matlab演示(Pattern recognition, perceptron training algorithm Matlab demo)
- 2010-01-11 10:01:09下载
- 积分：1
-
power_wind_dfig
MATLAB模型，双馈风电机组基于最大功率跟踪，低风速超速控制，中风速高风速变桨距控制(DFIG MATLABThe wind turbine and the doubly-fed induction generator (WTDFIG) are shown in the figure called The Wind Turbine and the Doubly-Fed Induction Generator System. The AC/DC/AC converter is divided into two components: the rotor-side converter (Crotor) and the grid-side converter (Cgrid). Crotor and Cgrid are Voltage-Sourced Converters that use forced-commutated power electronic devices (IGBTs) to synthesize an AC voltage from a DC voltage source. A capacitor connected on the DC side acts as the DC voltage source. A coupling inductor L is used to connect Cgrid to the grid. The three-phase rotor winding is connected to Crotor by slip rings and brushes and the three-phase stator winding is directly connected to the grid. The power captured by the wind turbine is converted into electrical power by the induction generator and it is transmitted to the grid by the stator and the rotor windings.)
- 2019-02-19 21:56:48下载
- 积分：1
