-
function
some notes abou svd in matlab functions
- 2010-12-16 01:59:38下载
- 积分：1
-
Blind_recognition_STBC
this code can be used in thesis for wireless communication thesis.
STBC based blind source separation method has been implemented in this code.
- 2014-09-02 12:16:02下载
- 积分：1
-
one_desiel_gen2014a
说明： 可以实现柴油发电机独立带负载运行，负载有常规负载和电动机负载，包含调速器部分和励磁控制部分(The diesel generator can operate independently with load. The load includes conventional load and motor load, including governor part and excitation control part.)
- 2021-01-02 14:48:57下载
- 积分：1
-
GA-TSP
说明： GA-TSP 运用遗传算法求解TSP问题，需要分开函数保存在运行。(GA-TSP the use of genetic algorithm to solve TSP problem and needs to separate the function is saved in the running.)
- 2010-03-26 16:34:47下载
- 积分：1
-
poission
泊松过程检测和估计。MATLAB。有详细的注释。(poission process.by MATLAB.)
- 2011-11-27 10:16:43下载
- 积分：1
-
matlab
迪杰斯特拉算法求最短路径，经典的求解最短路径算法等(Dijstrala algorithm solve the shortest—paths problems)
- 2010-07-12 20:54:07下载
- 积分：1
-
CVgray1
说明： 在matlab7中可以运行。其功能是实现用CV模型对灰色图像进行分割。(It Can be run in matlab7. function: It can make the gray image segmentation using the CV model .)
- 2010-04-26 22:15:46下载
- 积分：1
-
cooperative-communication
MIMO-OFDM的实现，不同点数的OFDM的实现以及SISO 和 MIMO之间的性能对比。(Implementation of MIMO-OFDM, OFDM, and the realization of the performance comparison of different points between SISO and MIMO.)
- 2014-01-19 14:36:36下载
- 积分：1
-
bottom_up_segmentation
这是TD算法的逆过程，首先将时间序列，划分为相邻点的短序列，当然此时的拟合误差为0，因为第一点和第二点的连线，原始点都落在线段上。将相邻两个线段连接起来，此时每条线段包含三个原始点，计算中间那个点的拟合误差。这样，所有这些三个点的线段中的中间点的拟合误差计算出来后，找出误差最小且误差小于阀值R的分段，作为第一条包含三个点的线段。 在上面的基础上，第一条分段同样的和相邻线段连接，然后计算每一条分段的拟合误差，再找出误差最小且小于阀值R的分段，作为第二个分段。依次方式循环，直到所有分段的拟合误差都小于阀值R，分段结束。
(This is the reverse process of TD algorithm, the first time series is divided into short sequences adjacent dots, of course fitting error is zero at this time, because the first and second points of connection, the original point fall line on. The two adjacent segments are connected, then each segment contains three original point, the intermediate fitting error calculated that point. Thus, after all these segments fitting error of three points in the intermediate point calculated to find the minimum error and the error is less than the threshold R segment, as the first line contains three points. Based on the above, the first segment and the adjacent line segment connecting the same, and then calculate a fitting error for each segment, and then find the smallest error and less than the threshold R segment, as the second segment . Followed by a cyclic manner until all segments fitting error is less than the threshold R, segment ends.)
- 2021-03-20 16:29:18下载
- 积分：1
-
motordrag
电动机拖动simulink模型，调节pi控制器的参数模拟控制效果，另附程序运行结果图(Drag motor simulink model, adjusting the parameters pi controller analog control results, an additional program to run the results of Figure)
- 2007-09-09 14:12:35下载
- 积分：1
