-
f2_51
转速反馈控制直流调速系统的仿真,该模型是转速负反馈闭环调速系统的MATLAB仿真模型(Speed feedback control DC drive system of the simulation, the model is a negative feedback loop Speed Control System of the MATLAB simulation model)
- 2010-09-20 22:05:17下载
- 积分:1
-
chaojihe
计数型抽样检验分析程序 按超几何分布计算(Counting of sampling inspection procedures by calculating the hypergeometric distribution)
- 2010-05-23 02:32:46下载
- 积分:1
-
CMA
基于恒模算法的自适应盲均衡,matlab代码(
Implements the Constant-Modulus algorithm for COMPLEX valued data)
- 2011-09-16 15:15:29下载
- 积分:1
-
matlab_eg
各种基本matlab实例精讲,以及详细的关于DFT的设计及其算法(Examples of basic matlab succinctly, and detailed design of algorithms for the DFT)
- 2011-11-12 13:00:08下载
- 积分:1
-
1
说明: 普通显示技术是根据几何光学成像原理,记录下光波的振幅,将空间物体成像在一个平面上。由于丢失了光波的相位信息,因而物体的信息是不完整的。全息图因能够完整地记录物光波的振幅和相位,因而能够包含物体的全部信息。菲涅耳全息术作为全息术的一个分支,更是得到了飞速的发展,已经广泛应用于全息干涉计量术、全息存储、全息光学组件、全息显微术等各个领域。
本论文主要研究菲涅耳全息图的编码与显示过程。经典光全息术包括波前记录和波前再现两步。全息波前记录将物光和参考光以干涉条纹记录成全息图,此全息图同时记录了物光波的振幅和相位 然后用参考光照射全息图,该参考光经过衍射后,即可再现出原始物体。
计算全息是将先进的计算机技术和光全息术结合起来,利用计算机产生全息图。它不需要物体实际存在,而是把物波的数学描述输入计算机处理后,绘制出全息图,然后用光学方法重现。本文采用计算全息方法,利用Matlab模拟光线的菲涅耳衍射传播,用计算机生成菲涅耳全息图 ,并由所生成的全息图再现出原始图像 ,完成全息图的数字再现。
(Fresnel hologram coding and display)
- 2015-12-10 16:12:19下载
- 积分:1
-
cl_matcontM2_2
说明: 计算动力学系统的分岔图,混沌系统,高维混沌系统的分岔图(Calculated bifurcation diagram of dynamical systems, chaotic systems, high-dimensional chaotic system bifurcation diagram)
- 2008-11-04 10:13:35下载
- 积分:1
-
newtonchazhi
说明: newton插值应该比lagrange好一点点,适合求解线性方程组,(lagrange interpolation newton than a little bit of good, suitable for solving linear equations,)
- 2008-11-19 11:32:41下载
- 积分:1
-
kftools
This set of MATLAB tools consists of some functions that I have
found useful for basic image processing and blob analysis. The
functions have been tested for MATLAB Version 5.3.0.10183 (R11) on
PCWIN. Many of the files must be run as MEX files (MEX files are
sometimes much faster than M-files). These must be compiled before
use by typing "mex filename.c" at the MATLAB command prompt where
filename.c is the relevant filename. Ensure that you are in the
correct directory (e.g. cd c:..KFtools) and that the KFtools
directory is included in the MATLAB path. The last three letters
of all of the functions that are implemented as MEX files are
m-e-x e.g. getboundarymex.(MATLAB This set of tools consists of some fu nctions that I have found useful for basic image processing and blob analysis. The functions ha 've been tested for MATLAB version 5.3.0.10183 ( R11) on PCWIN. Many of the files must be run as MEX files (MEX files are sometimes much faster than M-files). These must be compiled before use by t yping "Files filename.c" at the MATLAB command pr filename.c ompt where is the relevant filename . Ensure that you are in the correct directory (e . g. cd c : .. KFtools) and that the directory is KFtools included in the MATLAB path. The last three lett ers of all of the functions that are implemented MEX files are as m-e-x e.g. getboundarymex.)
- 2007-03-25 12:02:37下载
- 积分:1
-
paper
有关soi的资料,matlab对其各种特性进行仿真(Information about soi matlab simulation of its various characteristics)
- 2013-04-12 19:33:21下载
- 积分:1
-
SRM_CCC_PID4_LOAD0
开关磁阻电机的仿真模型,主要涉及是电流斩波控制,里面模型是MATLAB自带(a simulation model of switched reluctance motor,mainly about current chopping control)
- 2021-04-04 12:59:04下载
- 积分:1