-
The-PN-code-synchronous-simulation
PN码同步仿真输入 PN码同步仿真模块 PN码同步仿真输出(PN code synchronization simulation input PN code synchronization simulation module simulation output PN code synchronization)
- 2011-04-28 18:30:28下载
- 积分:1
-
example1
Metropolis within Gibbs sampling
- 2011-11-30 22:30:42下载
- 积分:1
-
stm32_eval
OMAP_MUX_MODE7 | AM33XX_PULL_ENBL | AM33XX_PULL_UP| AM33XX_PIN_OUTPUT
- 2013-12-30 17:07:45下载
- 积分:1
-
ZSource-inverter_Maximum-boost-control
Maximum boost control for z source inverter
- 2011-12-27 04:41:40下载
- 积分:1
-
my-data-1GDOP-for-GSM
matalb 雷达定位系统仿真 利用GDOP对性能进行评估 大家一起学习交流(matalb radar positioning system simulation use GDOP uate performance with everyone learning exchange)
- 2016-04-22 09:59:38下载
- 积分:1
-
lifting_97
本程序实现任意偶数大小图像第二代双正交97提升小波变换
注1: 采用标准正交方法,对行列采用不同矩阵(和matlab里不同)
注2: 为了保证正交,所有边界处理,全部采用循环处理
注3: 正交性验证,将单位阵带入函数,输出仍是单位阵(matlab不具有此性质)
注4: 此程序是矩阵实现,所以图像水平分量和垂直分量估计被交换位置
注5: 此程序实现的是类小波(wavelet-like)变换,是介于小波包变换与小波变换之间的变换
注6: 此程序每层变换相对原图像矩阵,产生的矩阵都是正交阵,这和小波包一致
注7: 但小波变换每层产生的矩阵,是相对每个待分解子块的正交矩阵,而不是原图像的正交矩阵
注8: 且小波变换产生的正交矩阵维数,随分解层数2分减少
注9: 提升系数可以在MATLAB7.0以上版本,用liftwave( 9.7 )获取,这里直接给出,考虑兼容性
注10:由于MATLAB数组下标从1开始,所以注意奇偶序列的变化
注11:d为对偶上升,即预测;p为原上升,即更新(err)
- 2008-06-25 07:59:17下载
- 积分:1
-
monituihuo
说明: 用模拟退火的算法解决中国旅行商的问题,结果画出图形直观明了!(Using simulated annealing algorithm to solve traveling salesman problem of China, resulting in intuitive and clear graphics to draw!)
- 2009-08-11 16:58:56下载
- 积分:1
-
fftc_
TI的FFT协处理器对应的源代码和matlab代码(Source code and matlab code corresponding to the FFT coprocessor of TI
)
- 2013-11-05 17:57:18下载
- 积分:1
-
AIAA-1994-3473-359
使用模糊自适应主动控制飞机起落架振动阻尼的研究(Using fuzzy adaptive active control landing gear vibration damping research)
- 2014-09-01 23:38:15下载
- 积分:1
-
LET
Lyapunov Exponents Toolbox (LET) provides a graphical user interface
(GUI) for users to determine the full sets of Lyapunove exponents
and dimension of their specified chaotic systems.
This version of LET can only run on MATLAB 5 or higher versions of
MATLAB. It has been tested under Windows and Unix. LET may also
run on other platforms.
The original version of LET has only 200 lines while the GUI version
of LET has almost 2000 lines. The GUI makes the program become more
sophisticated and run slower but allows the users to observe the
calculated results immediately, so that they can decide whether the
results are convergent or not.(Lyapunov Exponents Toolbox (LET) provides a graphical user interface (GUI) for users to determine the full sets of Lyapunove exponents and dimension of their specified chaotic systems. This version of LET can only run on MATLAB 5 or higher versions of MATLAB. It has been tested under Windows and Unix. LET may also run on other platforms. The original version of LET has only 200 lines while the GUI version of LET has almost 2000 lines. The GUI makes the program become more sophisticated and run slower but allows the users to observe the calculated results immediately, so that they can decide whether the results are convergent or not.)
- 2021-02-09 17:49:53下载
- 积分:1