-
Motioncontrolinfrastructureinlabview
几乎所有的自动设施一一从工业机器到医疗设备一一其组件如何移动都必须按照控制方式执行。移动负载最常见的方法就是使用一些电机元件如电动机。我们来学习如何控制基于电动机的系统，并探究NI公司所提供的各种不同的机器控制解决方案。(Almost all auto facilities one by one how to move from industrial machinery to medical equipment eleven components must be performed according to the control mode . Moving load is the most common method is to use some of the motor components such as motors. Let s learn how to control the motor- based systems)
- 2012-10-10 23:19:34下载
- 积分：1
-
hanshuxinhaofashengqi
1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口；
⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形；
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分：1
-
BP 神经网络labview
bp神经网络labview程序，使用labview实现BP神经网络的训练与应用(Bp neural network labview program, using labview to implement bp neural network training and application.)
- 2018-05-21 14:18:50下载
- 积分：1
-
NewportESP
NewPort平移台ESP301的控制程序，根据说明书自己编写的，不当之处请指正，串口通信，附有说明书。(Cord for Newport ESP301.)
- 2021-01-02 17:18:56下载
- 积分：1
-
LabVIEW-and-PLC
为了实现对船舶电站的实
时监控，对PLC编写程序，并在LabVIEW作为监控界面的情况，PLC与工控
机之间采用OPC技术实现通讯，GPC与工控机之间采用Modbus串口协议实现
通讯。最后在实现通讯的的基础上，对本系统进行了试验调试，并开发监控界
面。(In order to achieve real-time monitoring of ship power plant, the PLC programming and control interface as in the case of LabVIEW, PLC and IPC communication between the use of OPC technology, GPC and IPC used between the Modbus serial protocol communication. Finally, to achieve communication based on a test of the system to debug, and develop monitoring interface.)
- 2020-06-26 22:20:02下载
- 积分：1
-
labview九点标定
说明： labview与机械手的九点标定 手眼标定的实现(LabVIEW and nine-point calibration of manipulator)
- 2021-02-17 11:19:46下载
- 积分：1
-
Labview-and-PLC
本文件为labview源文件，实现labview和PLC的通讯。(This document is labview source file, realize labview and PLC communications.)
- 2020-06-26 22:40:01下载
- 积分：1
-
DataSocket
基于LabVIEW的datasocket的双机远程数据通信(Dual Remote Data Communication based the LabVIEW datasocket,)
- 2012-08-05 12:27:47下载
- 积分：1
-
labview九点标定
labview与机械手的九点标定 手眼标定的实现(LabVIEW and nine-point calibration of manipulator)
- 2021-02-17 11:19:46下载
- 积分：1
-
PID-control-of-DC-motor
基于Labview的直流电机闭环调速 稳定性好(Labview-based closed-loop DC motor speed control)
- 2015-04-07 12:58:27下载
- 积分：1
