登录
首页 » matlab » iec

iec

于 2013-08-20 发布 文件大小:1155KB
0 239
下载积分: 1 下载次数: 57

代码说明:

  IEC协会推荐的电压波动和闪变的测量计算方法,并含相关的IEC标准和国标(这些标准很难找到免费的)(IEC Association recommended voltage fluctuation and flicker measurement and calculation methods, and with the relevant IEC standard and GB (hard to find these standards for free))

文件列表:

新建文件夹
..........\GBT19862-2005电能质量监测设备通用要求[2].pdf,436258,2012-12-14
..........\GB_T_12326-2008 电能质量 电压波动和闪变.pdf,439925,2012-12-14
..........\IEC-61000-4-15-2003(1).pdf,443073,2013-07-24
..........\IEC1.mdl,37878,2011-04-19
..........\IEC2.mdl,32004,2009-04-11

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • ASVM
    ASVM 工具箱,包含ASVM的核心算法的MATLAB M文件(asvm toolbox)
    2009-06-03 21:42:40下载
    积分:1
  • up-to-air
    火箭升空动画,分为5个阶段,目前先上传一部分代码,后续继续(rock up to air flash)
    2012-03-27 04:52:57下载
    积分:1
  • computeitae
    用四阶龙格库特法在matlab环境下实现某函数的适应度值的计算。(A fitness function value is calculated using fourth-order Runge Ge Kute method in Matlab environment.)
    2012-07-21 10:47:27下载
    积分:1
  • KalmanAll
    this program describes the kalman filter used to reduce the error to get better accuracy of the position.
    2012-02-14 11:16:01下载
    积分:1
  • distribution
    说明:  检验已有的一组数据的概率分布是否为某种分布(Verify whether the data is a certain distribution)
    2019-05-09 13:39:38下载
    积分:1
  • pisa
    在计算机上产生一组实验数据,首先产生一段零均值白噪声数据u(n),令功率为 ,让u(n)通过一个三阶FIR: 得到y(n). .y(n)上加三个实正弦信号f1’=0.1,f2’=0.25,f3’=0.26调整 和正弦信号幅度信噪比大致为10dB,50dB,50dB. (1) 令N=256,描绘xn波形; (2)得出真实功率谱密度 . (3) 利用此实验数据Pisarenko谐波分解法估计该实验数据的正弦频率及幅度。 (On the computer to generate a set of experimental data, first generate a zero mean white noise data u (n), so that power, let u (n) through a third-order FIR: get y (n).. Y (n) added three real sinusoidal signal f1 ' = 0.1, f2' = 0.25, f3 ' = 0.26 and sine signal amplitude adjustment signal to noise ratio is approximately 10dB, 50dB, 50dB. (1) that N = 256, depicted xn waveform (2) the true power spectral density obtained. (3) using this experimental data, Pisarenko harmonic decomposition method to estimate the experimental data of the sinusoidal frequency and amplitude.)
    2010-10-22 11:17:41下载
    积分:1
  • PMSMmohuPIDkongzhi
    交流永磁同步电机模糊PID控制和单纯PID控制比较,突出模糊控制的 优点,可供学习模糊PID和电机的人参考。(AC permanent magnet synchronous motor PID control and fuzzy PID control relatively simple, highlighting the advantages of fuzzy control for learning and motor fuzzy PID Reference.)
    2020-11-20 14:49:36下载
    积分:1
  • part2
    盲信号处理研究论文,这是第二部分,包括三、四、五章以及摘要和目录。(Blind signal processing research papers, this is the second part, including three, four, five chapters, as well as a summary and directories.)
    2007-09-24 12:48:38下载
    积分:1
  • pro_2
    用局部参数最优化方法设计一个模型参考自适应系统,可调增益的初值Kc(0)=0.2,给定值r(t)为单位阶跃信号,即r(t)=A×1(t)。 要求: 1把连续系统离散化(采样时间可取0.1)。 2编制并运行这个系统的计算机程序(注意调整B值,使系统获得较好的自适应特性)。 3记录ym、yp的曲线 记录kp×kc的曲线 记录广义输出误差e的变化曲线。 4在参数收敛后,让Kp=2变为Kp=1,重新观察Kp×Kc及e的变化曲线。 5找出在确定的B值下,使系统不稳定的A值(阶跃信号的幅值),并与用劳斯稳定判据计算的结果比较。 (With local parameter optimization method to design a model reference adaptive system, adjustable gain initial Kc (0) = 0.2, for a given value of r (t) for the unit step signal that r (t) = A × 1 ( t). Requirements: a continuous system discretization (sampling time of 0.1 preferred). 2 compiled and run the system computer program (Note B to adjust the value of the system to obtain better adaptive characteristics). 3 records ym, yp curve record kp × kc curve records generalized output error e curves. 4 parameter convergence, let Kp = 2 into the Kp = 1, re-observed Kp × Kc and e curves. B-5 to find value in determining the next, making the system unstable A value (step signal of amplitude), and using Routh stability criterion and the comparison of the results calculated.)
    2010-09-03 14:27:08下载
    积分:1
  • sigshift
    说明:  此程序用语计算信号的位移是用MATLAB编写的,是一函数的形式可以直接调用 (Term this procedure the calculation of the displacement signal is prepared MATLAB is a function of the form can be directly called)
    2008-11-16 16:56:09下载
    积分:1
  • 696516资源总数
  • 106409会员总数
  • 8今日下载