-
55593406direct
研究可见光的程序仿真，其中包括的发射端和最后的接收端的功率分布图形具体程序，对于简单的研究有帮助(Studying the program simulation of visible light, including the specific program of power distribution graphics of transmitter and final receiver, is helpful for simple research.)
- 2018-11-15 11:16:02下载
- 积分：1
-
NewCSharpDesignPattern
新版设计模式手册[C#],设计模式 工程化(The new design Pattern manual [C#])
- 2009-05-05 11:03:37下载
- 积分：1
-
admin6
说明： 网页设计的一个框架，网上是付费的，再次公开源代码，以示分享(A framework for web design. Payment is made online and source code is made public again for sharing.)
- 2020-06-17 14:00:01下载
- 积分：1
-
CAN-Gateway_Functionality
说明： 本应用说明描述了Infineon MCU 基本的网关功能，并给出了如何设置外围寄存器的示例。(This Application Note describes the basic Gateway Functionality and gives an example on how to setup the peripheral registers.)
- 2020-06-23 17:00:02下载
- 积分：1
-
ConHDLFTB_15_5
cadence 培训教程
关于布局布线，期间封装(cadence training)
- 2011-12-27 13:13:47下载
- 积分：1
-
DLT698.45.Test
电网规约信息，可以解析电网698规约报文 ，供广大同仁参考(Power grid protocol information can be used to analyze 698 power grid protocol message for reference by colleagues.)
- 2020-06-20 20:00:02下载
- 积分：1
-
RequirementAnalyse
如何进行软件需求分析,内容非常详细。指出了一般进行需求分析时常犯的错误，帮助指导您理清头绪(How to carry out the software needs analysis, the content is very detailed. Pointed out that the general needs analysis carried out the mistakes from time to time to help guide you straighten out the threads)
- 2008-02-10 08:38:38下载
- 积分：1
-
optimize-
键是一种标准零件,通常用来实现轴与轮毂之间的周向固定以传递转矩，有的还能实现轴上零件的轴向固定或轴向滑动导向。在键连接设计时，间的高度和宽度根据轴的直径d选取，而键长L则根据轴上零件轮毂宽度B而定，通常L=B-（5—10）mm。键的尺寸确定后，再进行强度校核。而为了保证绝对安全，键的尺寸取值往往都趋于保守，所选键的尺寸大。本程序采用优化设计方法，在满足强度要求的前提下求出键的最小结构尺寸，证明键宽b和键高h的取值可以小于标准值。(Key is a standard part, often used to achieve between shaft and hub to transfer torque to a fixed week, and some can achieve a fixed axis or axial parts of the axial sliding direction. Key connection in the design, height and width between the shaft diameter d according to selection, and the bond length L is based on the width of the wheel shaft parts B and, typically L = B-(5-10) mm. Key size is confirmed, then strength check. In order to guarantee absolute security, key size values ??are often conservative, the size of the selected key to big. The program uses optimization methods to meet the strength requirements of the derived key premise of the minimum structure size, proved key width b and height h of the key values ??can be less than the standard value.)
- 2011-09-05 20:16:03下载
- 积分：1
-
LDC1000_F5529LP_DRDY
The 5th operation mode for the MSP430 integrated with the LDC1000
- 2020-06-21 18:40:02下载
- 积分：1
-
MT6260-GPIO-table_V1.0
MT6260 GPIO table_V1.0.xls
GPIO Config V1.0
- 2013-08-23 19:31:14下载
- 积分：1
