登录
首页 » matlab » scfde

scfde

于 2014-09-09 发布 文件大小:1KB
0 195
下载积分: 1 下载次数: 20

代码说明:

  matlab scfde source code

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 最佳升余弦滚降系统的多径传输
    最佳升余弦滚降系统的多径传输. 滚降系数0.5, 取样时间无偏差.(best Raised Cosine system multipath transmission. Roll-off coefficient of 0.5, sampling time without deviation.)
    2005-03-26 20:36:51下载
    积分:1
  • convertTDMS
    导入LabView的TDMS的文件作为一个在与选择保存在文件中的数据在垫子MATLAB的工作空间的结构(版本1.1或1.2)。这是写在MATLAB2010b。原函数的基础上,由Brad堪寻的技术和格兰特Lohsen与杰夫Sitterle的GTRI(通过此功能4版本1)的工作。版本9功能(菲利普上编写的),除加入了添加的各种以前的版本更新,可以处理已被“优化“由LabVIEW文件。这个功能已经测试了多种TDMS的文件数量有限。(Import a LabView TDMS file (version 1.1 or 1.2) as a structure in the MATLAB workspace with the option to save the data in a MAT file. It was written in MATLAB 2010b. The original function was based on the work by Brad Humphreys of ZIN Technologies and Grant Lohsen & Jeff Sitterle of GTRI (versions 1 through 4 of this function). The Version 9 function (written by Philip Top), in addition to incorporating the various updates that were added to previous versions, can process files that have been "optimized" by LabView. This function has been tested with a limited number of diverse TDMS files.)
    2011-05-23 11:28:47下载
    积分:1
  • sky
    利用天棚原理对车辆悬架进行控制,天棚控制又卡诺怕于1970s提出。(Ceiling suspension using the principle of control of the vehicle, ceiling control and fear in the 1970s raised Carnot.)
    2013-09-12 04:21:29下载
    积分:1
  • Fault-diagnosis-System
    机械故障诊断方法概述 信号处理方法概述 齿轮箱故障诊断(Mechanical fault diagnosis method outlined signal processing method outlined gearbox fault diagnosis)
    2014-12-23 11:00:32下载
    积分:1
  • MATLABcPP
    MATLAB与c++混编的案例代码,可运行,是学习的好例子(MATLAB and c++ mixed case code can be run, is a good example of learning)
    2014-01-29 17:41:01下载
    积分:1
  • eemscat
    去除三维荧光光谱拉曼散射、瑞利散射、二级瑞利散射。matlab m文件(The purpose of the interpolation is to replace the data in the gray areas with new data consistent with the data in the remaining parts of the EEM.)
    2021-04-27 21:08:44下载
    积分:1
  • MS_matlab
    分割算法 1.mean shift 的迭代过程只做了一次(为了简单) 2.对图像中的某一点进行平移时,只考虑了距离它小于2*hr的点,而不是图像中所有的 点。 3.实验过程中只用到了gauss核,虽然提供了method的选择,但在进行值域加权时只用 到gauss核,如果需要请自己改正。(mean shift algorithm )
    2009-03-24 20:09:34下载
    积分:1
  • HBMA
    说明:  以MATLAB做HBMA的碼源,輸入兩個圖片可以找出前後的residual(HBMA do to MATLAB source code, enter the two pictures can be found around the residual)
    2008-12-03 17:01:59下载
    积分:1
  • modul-matlab
    modul pelatiah matlab berbahasa indonesia
    2014-02-11 11:05:01下载
    积分:1
  • bernoulli
    This MATLAB code from MATLAB central file
    2009-12-08 00:18:34下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载