登录
首页 » matlab » NOLOADSS

NOLOADSS

于 2010-07-14 发布 文件大小:1KB
0 193
下载积分: 1 下载次数: 90

代码说明:

  风力发电空载运行实施并网控制S函数优化代码,实现了风力发电空载运行时发电机模型的M语言编程 (Wind Power Generation Operation and Network Control S functions implementing optimized code and realized the wind power generator no-load run-time programming model M)

文件列表:

NOLOADSS.m,913,2010-07-14

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • bpsk
    bpsk误码率,做毕业设计常用到的哦,题目是单入单出系统的误码率和信噪比的关系图(bpsk error rate, used to do Oh graduation, into a single topic is the system single-bit error rate and signal to noise ratio graph)
    2011-05-09 21:59:15下载
    积分:1
  • hamilton
    经典的汉密尔顿回路算法,以Matlab代码编写。(Hamilton classic loop algorithm to Matlab coding.)
    2008-12-15 14:38:33下载
    积分:1
  • Untitled
    在加入高斯白噪声的情况下,假设信噪比为10dB,形成传统波束形成法、Bartlett波束形成法、Capon波束形成法的空间谱图(Prior to joining the case of white Gaussian noise, assuming the SNR is 10dB, the formation of conventional beamforming method, Bartlett beamforming method, Capon Beamforming spectrum of space law)
    2011-05-05 23:13:50下载
    积分:1
  • the-command-ofmatlab-simulink
    matlab仿真工具(simulink)的命令集(the command ofmatlab simulink)
    2012-05-15 19:25:59下载
    积分:1
  • WOA灰狼算法
    说明:  灰狼优化算法,直接就能用,里面包含有23种测试函数,做实际应用时,需要调一下。(Gray wolf optimization algorithm, which can be used directly, contains 23 kinds of test functions, and needs to be adjusted in practical application.)
    2021-03-25 10:49:14下载
    积分:1
  • homework
    该代码可用于对红外图像的高低温图分别进行一点校正和两点校正(This code can be used for infrared images were a little high and low figure correction and two-point calibration)
    2015-01-10 11:13:47下载
    积分:1
  • cla
    追赶法求解矩阵;牛顿插值函数,三次样条插值函数仿真龙格库塔现象;二分法求解根与牛顿迭代,弦割法,简单迭代法的程序(Section three order spline interpolation function Newton interpolation Iterative method)
    2014-01-10 22:06:51下载
    积分:1
  • matlab
    首先对图像进行了边缘检测,设计相应的结构元素对图像进行腐蚀,再进行图像聚类和填充图像。(First, the image edge detection, the design of structural elements corresponding to the image etched image clustering and then fill the image.)
    2014-02-20 22:00:29下载
    积分:1
  • GoldLow
    周期不大于127的扩频序列生成程序,可用于matlat的RAKE接收仿真.(Not more than 127 cycles of the spread spectrum sequence generation process, can be used for the RAKE receiver matlat simulation.)
    2009-05-12 11:54:32下载
    积分:1
  • KPCA11
    自己尝试编写的核主元分析(KPCA)程序(Try to write a kernel principal component analysis ( KPCA ) program)
    2012-04-19 16:43:24下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载