-
04785259
AN MATLAB DESIGN OF PV ARRAY PAPER
- 2013-05-02 18:30:49下载
- 积分：1
-
main
rake接收的matlab代码，不是simulink(rake receiver of the matlab code, not the simulink)
- 2010-07-14 16:28:41下载
- 积分：1
-
VSR_double
simulink环境下的双极性PWM控制的单向电压型整流器的模型(simulink environment bipolar PWM control unidirectional voltage source rectifier model)
- 2013-08-04 17:54:40下载
- 积分：1
-
matlab5
利用matlab进行频域低通和带通滤波,效果不错(Frequency domain using matlab low-pass and band-pass filtering)
- 2013-09-15 10:48:39下载
- 积分：1
-
EKF_nonGaussian
新型的EKF算法，用于估计汽车用锂电池的电池SOC(New EKF algorithm for estimating automotive lithium battery SOC)
- 2015-01-04 11:03:18下载
- 积分：1
-
program-and-data-sets
本程序是用于在时域中分析处理轴承故障数据的，提取了各种时域的特征参数，包括均值，有效值，峭度，裕度指标，波形指标等等 适合初学者用于轴承的故障诊断中对参数的提取。（附上轴承故障数据3类共21组 正常、内圈、外圈）(This procedure is used in the time domain analysis of bearing fault data processing to extract the characteristics of various time domain parameters, including mean, RMS, kurtosis, margin indicators, wave indicators, and so suitable for beginners for bearings Fault diagnosis of parameter extraction.)
- 2021-04-25 22:58:46下载
- 积分：1
-
Bluetooth_Full_Duplex
Simulink® and Stateflow® model of a full duplex Bluetooth communication link transmitting HV1, HV2, HV3, and SCORT [1] voice packets, and DM1 data packets. A system parameters block configures the whole model s packet type, slot pair and channel type. Stateflow is used to implement the acknowledgement scheme for the data packets and the SCORT receiver state machine.
NOTE: A version of this model which works with the current release of MATLAB and Simulink is shipped with the Communications Blockset™ .
The model includes wave file I/O, CVSD speech coding, HEC, payload CRC for DM1, FEC, framing, GFSK Modulation, frequency hopping, hop sequence generation, an 802.11b interferer, BER meters, throughput meters, plus spectrum, timing and spectrogram plot (which can be turned-off).
- 2015-02-04 04:09:00下载
- 积分：1
-
activeContoursSnakesDemo
本演示实现了主动轮廓模型由Kass等人提出。
要运行它的图形用户界面
1。基于MATLAB型引导提示。
2。关于“到现有的图形用户界面，点击”
3。选择在与本文件相同的目录snk.fig文件
4。按一下上方的绿色箭头启动图形界面
一旦GUI已经启动，您可以通过使用蛇
1。点击“新形象”，并加载输入图像。提供的样品图像。
2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。
3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。
4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al.
To run it with GUI
1. Type guide on the matlab prompt.
2. Click on "Go to Existing GUI"
3. Select the snk.fig file in the same directory as this file
4. Click the green arrow at the top to launch the GUI
Once the GUI has been launched, you can use snakes by
1. Click on "New Image" and load an input image. Samples image are provided.
2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image.
3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points.
4. Set the various snake paramete)
- 2010-07-05 11:54:13下载
- 积分：1
-
NNX142
MATLAB环境下的BP网络的实现，源程序，对于在matlab下做神经网络仿真的各位有帮助。(MATLAB environment BP network realized, source files, For Matlab neural network simulation do you have any help.)
- 2007-05-30 08:40:22下载
- 积分：1
-
cluster-1.36.tar
source codes for clustering algorithm
- 2007-10-18 15:08:00下载
- 积分：1
