-
crc32
I was suprised LabVIEW didn t had the CRC32. So I made it, http://en.wikipedia....edundancy_check, http://www.ietf.org/rfc/rfc1952.txt. It can take a array of U32, one element of U32 or a string. When needed I can create more CRC checks, CRC8, CRC16, etc... but CRC32 is the most used one I readed.
- 2014-10-03 08:36:43下载
- 积分：1
-
坐标系转换
说明： 将直角坐标系数据转换成极坐标数据，以便绘制主轴轴心轨迹(Converting Cartesian coordinates into polar coordinates to plot axis center trajectory)
- 2019-02-27 16:25:15下载
- 积分：1
-
示波器测试版1.5
可以对单次输入的信号进行滤波分析和图像显示。同时也具备暂停和历史图像保存的功能。
本程序主要针对的是低频率的未知信号，对于高频率信号最好采用单次采样的方式。(The single input signal can be filtered and analyzed, and the image can be displayed. It also has the functions of pausing and preserving historical images.
This program is mainly for low frequency unknown signals, for high frequency signals, the best way to use a single sampling.)
- 2020-06-20 09:20:01下载
- 积分：1
-
sjcj
LabVIEW编程语言实现振动信号的多通道数据采集(LabVIEW programming language to achieve multi-channel data acquisition of the vibration signal)
- 2012-07-22 21:02:27下载
- 积分：1
-
数据采集编程指南 中篇
说明： NI DAQ应用介绍
1. 一个完整数据采集系统的基本组成部分
2. NI 提供了基于哪些平台的数据采集硬件产品，它们分别适用于什么样的应用领域
3. 数据采集设备硬件选型过程中应该关注哪些重要参数(Introduction of NI data acquisition hardware 1. Basic components of a complete data acquisition system 2. NI provides data acquisition hardware products based on which platforms and which application areas they are suitable for respectively. 3. What important parameters should be paid attention to in the process of hardware selection of data acquisition equipment)
- 2020-06-21 20:20:01下载
- 积分：1
-
keyboard
说明： 程序显示如何在labview中读取键盘、鼠标和操纵杆(recognition of keyboard input, mouse input and joystick input)
- 2019-03-04 15:36:07下载
- 积分：1
-
2009
基于LabVIEW的超声信号小波阈值去噪方法，是种很实用的消噪方法(Based on LabVIEW ultrasound signal wavelet threshold denoising method is very practical denoising)
- 2012-07-06 17:16:21下载
- 积分：1
-
daq
本文主要介绍了利用国产普通数据采集卡，基于美国 NI 公司提供的虚拟仪
器软件开发平台 LabVIEW 和实验室原有发动机硬件平台自行开发的一套气缸压
力采集模块和数据分析模块(This thesis primarily introduced software about cylinder pressure and crank
angle acquisition and data analysis module. It is designed by using a general data
acquisition board, which is based on Virtual Instrument LabVIEW offered by NI and
laboratory engine.
)
- 2013-05-23 20:34:34下载
- 积分：1
-
多连接TCP
说明： 可实现TCP/IP连接后数据的读取与写入(TCP/IP data read and write)
- 2020-01-19 12:07:42下载
- 积分：1
-
测试
说明： labview实现串口示波器的功能，读取示波器发送的浮点数数据，并绘制曲线(Serial port oscilloscope)
- 2019-10-23 13:37:02下载
- 积分：1
