-
UI Messages TestStand LabVIEW OI
说明： 客户觉得TestStand界面复杂，希望一个简单的界面即可进行序列执行，采用LabVIEW调用TestStand引擎可实现快速设计，将TestStand拆解到LabVIEW。
然而，这样做需要设计大量回调函数，开发较费时间，项目对时间要求很严格，且投入不多，故希望有快速解决方案。
为此，设计时希望LabVIEW可以充当一个辅助软件，可配置和控制执行，进行简单数据交互，执行还是TestStand进行(The customer thinks that TestStand interface is complex, and hopes that a simple interface can be used for sequence execution. Using LabVIEW to call TestStand engine can realize rapid design and disassemble TestStand to LabVIEW. However, to do this, a large number of callback functions need to be designed, which takes a lot of time to develop. The project has strict time requirements and little investment, so we hope to have a fast solution. Therefore, it is hoped that LabVIEW can be used as an auxiliary software in the design, which can be configured and controlled for execution, simple data interaction, execution or TestStand)
- 2020-06-01 17:19:22下载
- 积分：1
-
labview与PLC通讯范例
实现上位机与台达PLC的MODBUS RTU通信,输入命令和地址后直接可以用(comulication for pc and PLC)
- 2018-11-07 13:41:40下载
- 积分：1
-
声级测量2
使用labview来采集声音及处理，三分之一倍频等(Acquisition of voice and processing)
- 2018-09-14 15:46:26下载
- 积分：1
-
SVMS-1.0.2
LabView土木信号处理方面基于Labview的传感信号采集处理程序及说明资料(LabView signal processing)
- 2014-05-02 13:53:54下载
- 积分：1
-
基于LabVIEW的通用自动测试系统设计
说明： 基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)
- 2020-10-24 12:27:23下载
- 积分：1
-
SD-HHT
对LabVIEW进行二次开发，对振动信号进行HHT时频分析(LabVIEW second development, vibration signals HHT time-frequency analysis)
- 2012-07-22 20:53:00下载
- 积分：1
-
TCP客户端程序
基于labview的TCP客户端程序发送主机通常将发送缓冲区中的数据按内存地址从低到?的顺序发出,接收主机把从?络上接到的字节依次保存在接收缓冲区中,也是按内存地址从低到?的顺序保存。
TCP/IP协议规定,?络数据流应采??端字节序,即低地址?字节。
socket API是?层抽象的?络编程接?,适?于各种底层?络协议,如IPv4、 IPv6,以及后?要讲的UNIX Domain Socket。(Based on the TCP client program to send the host LabVIEW will usually send buffer according to the data in the memory address from low to order issued, the receiving host to receive from the network bytes on sequentially stored in the receive buffer, and according to the memory address from low to preservation order.
The TCP/IP agreement, network data flow should be endian, low byte address.
Socket API is layer abstract network programming interface, suitable in various underlying network protocol, such as IPv4, IPv6, and UNIX Domain Socket to say.)
- 2018-01-15 01:19:31下载
- 积分：1
-
Practica-1
In this program we put any temperature and the program will show us with booleans if there is a problem about the temperature
- 2016-10-21 04:16:51下载
- 积分：1
-
soundcardoscillograph
利用图形化语言LabVIEW开发的用的基于声卡的虚拟示波器(The use of LabVIEW graphical development language to use virtual sound card based oscilloscope)
- 2009-05-07 19:44:38下载
- 积分：1
-
《我和+LabVIEW》示例程序
《我和+LabVIEW》示例程序 Sample Program of "I and + LabVIEW"(Sample Program of "I and + LabVIEW")
- 2020-06-24 15:40:02下载
- 积分：1
