-
REWIND_D31_StandardizationDocument_v12
This document is an stansardization activity of MMR WiMAX networks done by REWIND project team
- 2010-07-27 11:30:51下载
- 积分：1
-
Kalman(1)
运用matlab语言编制的卡尔曼滤波程序。(matlab kalman)
- 2012-04-18 15:02:11下载
- 积分：1
-
droopgridsingle
说明： 并网下垂控制仿真，单台并网逆变器，采用下垂控制(Simulation of grid-connected sag control, single grid-connected inverter, using sag control)
- 2020-10-05 20:27:38下载
- 积分：1
-
Matlab-code
英文原版书籍《MATLAB Programming With Applications for Engineers》中例子及课后习题代码(Code of the book《MATLAB Programming With Applications for Engineers》)
- 2013-12-17 07:25:05下载
- 积分：1
-
cma
channel estimation in ofdm
- 2012-04-24 21:06:03下载
- 积分：1
-
05
说明： Study of an energy conversion chain
wind based on a AEROTURBINE
- 2015-02-07 19:52:53下载
- 积分：1
-
hspice
this will u in HSPICE tools
- 2009-12-13 02:16:45下载
- 积分：1
-
elm_kernel
ELM 极限学习机的核函数 MATLAB程序，用于深入研究和改进极限学习机(Kernel MATLAB program ELM Extreme Learning Machine for further research and improvement Extreme Learning Machine)
- 2021-04-01 13:59:08下载
- 积分：1
-
模拟退火
说明： 模拟退火算法来源于固体退火原理，是一种基于概率的算法，将固体加温至充分高，再让其徐徐冷却，加温时，固体内部粒子随温升变为无序状，内能增大，而徐徐冷却时粒子渐趋有序，在每个温度都达到平衡态，最后在常温时达到基态，内能减为最小。(Simulated annealing algorithm is derived from the principle of solid annealing is a kind of algorithm based on probability, high solid heating to fully, then let it slowly cooling, heating, inside the solid particles with the temperature rise to disorder, internal energy increase, and slowly cooling particles become more orderly, and in each temperature to reach the equilibrium state, finally reach the ground state in normal temperature, can reduce to a minimum.)
- 2021-02-24 15:47:10下载
- 积分：1
-
1122
其实操作系统在调用 main 函数时是传参数的，main 函数最标准的形式应该是 int
main(int argc, char *argv[])，在第 6 节 “指向指针的指针与指针数组”
详细介绍。C 标准也允许 int main(void)这种写法，如果不使用系统传进来的两
个参数也可以写成这种形式。但除了这两种形式之外，定义 main 函数的其它写法都
是错误的或不可移植的。(The 88-bytes (704-bits) in the Configuration zone contain manufacturing identification data, general device, and
system configuration, and access restriction control values for the slots within the Data zone. The values of
these bytes can always be obtained using the Read command. The bytes of this zone are arranged as shown in
Table 2-2)
- 2015-01-05 17:13:58下载
- 积分：1
