登录
首页 » matlab » point23

point23

于 2011-10-07 发布 文件大小:1KB
0 182
下载积分: 1 下载次数: 3

代码说明:

  Antenna and EM Modeling with MATLAB

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • gsw_delta_SA
    求取绝对盐度用新海水状态方程来求取这是新的海水状态方程(Absolute salinity water to strike the state equation with the new strike)
    2011-05-27 19:15:09下载
    积分:1
  • f_sin
    matlab编写的复正弦信号频率估计程序,分别计算Tretter方法、kay、lovell&williamson等方法(matlab write complex sinusoidal signal frequency estimation procedures were calculated the Tretter method, kay lovell & williamson other methods)
    2012-08-21 10:27:56下载
    积分:1
  • INS-solver
    由惯性器件的输出解算出飞行器的位置、速度、姿态信息(The output from the inertial device solves for the aircraft position, speed, attitude information)
    2013-09-02 19:23:52下载
    积分:1
  • GPC_J
    多约束的广义预测控制算法。使用fmincon求解(GPC with constrains code is proposed. And fmincon function is uesed.)
    2013-04-11 10:09:18下载
    积分:1
  • costas
    科斯塔斯环载波恢复,用来跟踪输入信号的载波频率(carrier recovery by costas loop)
    2011-12-20 19:54:31下载
    积分:1
  • simulation
    在求解装备的资源约束型装配线一类平衡问题时,借助遗传粒子群算法进行优化求解,并对遗传粒子群算法进行改进,利用matlab程序进行优化求解。本次结果是进行仿真的结果。(When solving the resource-constrained assembly line balance problem of equipment, the genetic particle swarm optimization algorithm is used to optimize the solution, and the genetic particle swarm optimization algorithm is improved, and the matlab program is used to optimize the solution. This is the simulation result.)
    2019-04-29 16:44:26下载
    积分:1
  • Cox
    利用三次样条函数考察Cox模型比例风险假定.rar(Use of cubic spline function inspection Cox proportional hazards model assumptions. Rar)
    2009-03-16 17:05:01下载
    积分:1
  • NumAna_GaussElim
    这四个程序分别为高斯消去法、列主元消去法、全主元消去法解线性方程组和Gauss-Jordan消元法求矩阵的逆。   程序采用MATLAB语言开发,并在MATLAB6.5下测试通过。(The four procedures were Gaussian elimination, elimination method out PCA, PCA-wide elimination method solution of linear equations and Gauss-Jordan elimination method of inverse matrix. Procedures for the use of MATLAB language development, and under MATLAB6.5 test.)
    2007-12-24 16:56:06下载
    积分:1
  • S1C
    function [ret,x0,str,ts,xts]=s4(t,x,u,flag) s4 is the M-file description of the SIMULINK system named s4. The block-diagram can be displayed by typing: s4. SYS=s4(T,X,U,FLAG) returns depending on FLAG certain system values given time point, T, current state vector, X, and input vector, U. FLAG is used to indicate the type of output to be returned in SYS.
    2010-03-03 17:27:43下载
    积分:1
  • Giao-trinh-matlab-DKTD
    This is ebook by vietnamese ,to using matlab easy to difficuilt, in this book you can learn so much information about matleb
    2012-09-06 13:53:49下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载