登录
首页 » matlab » Rotor-rubbing-the-bifurcation

Rotor-rubbing-the-bifurcation

于 2013-09-23 发布 文件大小:1KB
0 174
下载积分: 1 下载次数: 75

代码说明:

  转子碰摩非线性计算,可计算出p1,p2,倍周期分岔,混沌等特性(Rotor rubbing the bifurcation diagram matlab source code)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • shuangkuiwenxian
    双馈电机matlab中的仿真模型文献,有风力机的介绍(Modeling and Simulation of Doubly—Fed Induction Wind Power System Based on Matlab/Simulink)
    2013-01-07 08:59:58下载
    积分:1
  • dnzljc
    在电能质量检测中暂态信号和稳态信号的建模的源程序(Power quality detection of transient and steady-state signal source)
    2013-04-10 15:41:53下载
    积分:1
  • ESSAI4
    9 BUS SIMPOWERSYSTEMS MODEL
    2014-01-09 08:15:58下载
    积分:1
  • SMQT-SNoW-face-detection
    Face Detection using local SMQT features and split up SnoW classifier
    2010-07-19 11:05:06下载
    积分:1
  • BPsjwl
    matlab编程,采用BP神经网络对信号进行分析(Matlab programming, using BP neural network to analyze the signal)
    2013-04-09 19:39:41下载
    积分:1
  • calculate_farfield
    计算天线阵列远场方向图,支持各种幅度加权,相位加权,可自行指定阵元方向图(calculate the farfield of an antenna array with various degrees of freedom)
    2013-12-24 09:40:07下载
    积分:1
  • sudoku
    用matlab程序自编的数独程序,可以解决大部分的9*9宫格的数独。(Sudoku program, self matlab program can solve most of the 9 x 9 Sudoku grids.)
    2013-03-11 20:17:34下载
    积分:1
  • ssm
    ssm in sine wave modulation
    2012-11-16 23:16:33下载
    积分:1
  • fcmC
    在原始的 fcm 算法基础上,对算法中的聚类数 c 和加权指数 m 给出优选方法, 进而而出了 fcm 参数优选自适应算法,通过人造数据与具有实际背景的数据验证可以看出 该算法是有效的,该算法不但可以自适应的给出最佳的聚类数,而且可以验证聚类的有效性, 达到最佳聚类的目的(Fcm algorithm in the original, based on the number of clustering algorithms and the weighted index m given c preferred method, and then out of the fcm parameter optimization adaptive algorithm, synthetic data and practical background in data validation can be seen that the algorithm is effective, the adaptive algorithm can not only give the best number of clusters, and clustering can verify the validity of the purpose to achieve the best clustering)
    2011-05-21 11:03:15下载
    积分:1
  • 半车模型
    半车模型,考虑车辆悬架,前后俯仰等自由度,利用S函数编写(Half car model, considering vehicle suspension, front and rear elevation and other degrees of freedom, the use of S-function written)
    2020-07-04 00:40:01下载
    积分:1
  • 696518资源总数
  • 105540会员总数
  • 37今日下载