-
Matlab_tablot
文件包中12个程序基于Matlab开发Talbot成像的计算软件,非常好,请大家试用.(The package included 12 softwares for Talbot effect in matlab)
- 2009-10-05 14:16:32下载
- 积分：1
-
resample2
重采样MATLAB程序2例参考程序。用于对信号进行不同采样频谱的采样(resampling)
- 2010-01-19 15:17:44下载
- 积分：1
-
leaf-area-ref-2
leaf area measurment
- 2012-05-18 18:39:50下载
- 积分：1
-
godem
this code is simple and usful code it is a matlab code that optimize PID parametrs using Generic Algorithm
- 2011-12-06 22:02:48下载
- 积分：1
-
Graph_matlab
《图论算法及其matlab实现》的部分原始m文件，免去了自行键入的烦恼，很便捷(" Graph Theory Algorithm and Its Implementation matlab" m part of the original document, which eliminates the trouble of their own type, it is convenient)
- 2010-05-22 17:29:14下载
- 积分：1
-
fuzzylogic
controller design for pendulum
- 2014-01-02 01:14:00下载
- 积分：1
-
ErrDetectSplot
一个定时误差检测器的特性由其曲线来表征。误差检测灵敏度一般取误差检测器曲线在零定时误差附近的斜率。(The characteristics of a timing error detector is characterized by the curve. Error detection sensitivity generally take near zero timing error detector curve slope.)
- 2017-07-26 16:08:59下载
- 积分：1
-
ovsf
ovsf is an orthogonal code for multiuser environment
- 2009-11-14 11:23:34下载
- 积分：1
-
phone_matlab
基于MATLAB的按键式电话信号检测实现(MATLAB-based touch-tone phone signal detection to achieve)
- 2011-09-02 09:42:48下载
- 积分：1
-
项目4
说明： 任务：设计一个4×2.5Gbit/s 长距离光纤传输系统，并利用OptiSystem 仿真验证。
要求：
1．采用波分复用技术，波长设置以100GHz 为间隔，频率分别为193.1THz、193.2THz、193.3THz、193.4THz，每个波长传输速率为2.5Gbit/s（NRZ），传输距离为300km。采用常规光纤，光纤损耗系数为0.25dB/km。
2．单通道光发送机最大输出功率为0dBm，光接收机的接收光功率不低于－26dBm，过载点为－10dBm。
3．可以采用EDFA 作为线路放大器，其中EDFA 的输入功率限制在－18～2dBm，最大输出功率20dBm，增益范围为13～25dB，噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify.
Requirement:
1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km.
2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm.
3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
- 2019-05-13 09:39:41下载
- 积分：1
|
联系客服（QQ：3324461878）
