-
Mimotools
code matlab for mimo system
- 2009-12-09 17:52:05下载
- 积分：1
-
sabrmc
金融工程中关于SABR问题的求解，使用蒙特卡洛方法(Stochastic Alpha Beta Rho Model，Monte Carlo)
- 2011-04-22 14:05:46下载
- 积分：1
-
Image-Denoising
This matlab code for removal of noise from images of rgb and grey type.
- 2013-03-06 22:10:27下载
- 积分：1
-
modulePparticlePfilter
这是用于目标跟踪的粒子滤波代码，
用matlab编写的，很有借鉴性，一维情况下，
非高斯非线性，其中将扩展卡尔曼滤波与粒子滤波进行比较，更好的说明了粒子滤波的优越性(This is a particle filter for target tracking code using matlab, referential nature, one-dimensional case, the non-Gaussian non-linear, which will be extended Kalman filter and particle filter to compare, a better description of the particle the superiority of the filter)
- 2012-08-16 16:15:35下载
- 积分：1
-
matlab
基于MATLAB对图形图像进行多方面的处理，先图形直方图均衡处理，再通过积分投影，分别为水平投影，垂直投影，再则进行精确定位目标(MATLAB-based graphical images on a wide range of processing, the first graphical histogram equalization processing, and through the integral projection, horizontal projection, vertical projection, she then accurately locate targets)
- 2009-12-23 19:28:29下载
- 积分：1
-
xunhuanbaoshu
这个程序针对的问题是: 17个人为成圈,依次编号为0-16,从第一号开始报数,报到3的倍数的人离开, 一直数下去,直到最后只剩1人,求此人的编号. 程序有点复杂，不过还只能算是初级的水平 (This procedure for the question is: 17 individuals into the circle, followed by numbered 0-16, from the first to begin reported the number of people who report a multiple of three to leave, to keep counting votes until the last only a person seeking this person number. program a bit complicated, but can only be considered the primary level of)
- 2010-01-27 01:17:44下载
- 积分：1
-
msk
说明： msk调制解调程序，利用matlab进行仿真，通信类设计可用(msk modulation and demodulation process simulation using matlab, Communications design available)
- 2010-04-12 08:36:20下载
- 积分：1
-
FDTDdotsource
二维点光源Maxwell方程组FDTD程序，采用吸收边界条件(Two-dimensional point source Maxwell equation FDTD procedure for absorbing boundary conditions)
- 2020-09-10 16:08:00下载
- 积分：1
-
BLDCM
无刷直流电机的控制模型，根据实际的仿真结果，能够得到很好的仿真效果，结构理想，很好(failed to translate)
- 2013-05-08 20:11:56下载
- 积分：1
-
signal_analyzer(1)
主要内容(signal_analyzer.rar)如下：
test1.txt 第一列为时间t，0.001s为步长；第二列为系统的输入信号；第三列为系统的输出信号。
signal_analyzer.m首先将test1.txt 的数据读入workspace，然后进行FFT，分析出两信号的频率，输出对于输入的幅值衰减（db），输出对输入的相位差。
(Main Content (signal_analyzer.rar) as follows: test1.txt the first time as t, 0.001s for the step the second as the input signal the third as the system output signal. signal_analyzer.m first test1.txt the data read into the workspace, and then FFT, the frequency of the two signals, the output amplitude for input attenuation (db), the output of the input phase difference.)
- 2010-05-18 15:57:01下载
- 积分：1
