-
matlab_GUI
英文版，内容全面详尽。是学习Matlab GUI的一本很好的入门教材(English, comprehensive and detailed. Is to learn Matlab GUI' s a good primer)
- 2010-06-03 13:44:32下载
- 积分：1
-
numerical-analysis-matlab-GUI
说明： 数值分析程序
matlab-GUI(numerical analysis
matlab GUI)
- 2010-03-24 17:19:34下载
- 积分：1
-
PID_Controller
matlab中PID控制系统仿真模型，算法简单、稳定性好、可靠性高(PID control system simulation model in matlab, simple algorithm, good stability, high reliability)
- 2012-08-10 12:23:58下载
- 积分：1
-
TheCalculationandAnalysis
利用二维有限差分法对单脊波导TM模进行计算。通过调整网格数目观察计算结果的精度，可以设定出最优的网格数目，然后改变波导中脊的尺寸，观察最低两个TM模对应的截止频率的变化规律，最后给出对应的横截面电场、磁场分布图(The two-dimensional finite difference method to calculate the single-ridge waveguide TM mode. The optimal number of grid can be set by the accuracy of the adjustment of the calculation result of the grid number observed, and then change the size of the waveguide ridge observed the lowest two corresponding to the TM mode of the cutoff frequency of the variation, and finally to give the corresponding cross cross-section of the electric field, magnetic field maps)
- 2013-03-18 12:22:11下载
- 积分：1
-
text2
用Simulink中的SimPowersystem完成一个转速、电流双闭环直流调速系统的设计与仿真。采用三相桥式整流，平波电抗器Lp的大小可根据根据仿真调整。给出电机在空载启动，以及在2.5S后加额定负载时转速、电流、电压的变化曲线，并结合调速理论分析这些曲线。(With Simulink in SimPowersystem complete a speed, current double-loop DC speed design and simulation system. Three-phase bridge rectifier, smoothing reactors Lp size can be adjusted according to the simulation. Start the motor load is given, and the speed curve when the rated load after 2.5S, current, voltage, speed and theoretical analysis of these binding curves.)
- 2014-01-17 09:43:22下载
- 积分：1
-
SegTool
lazy snapping的算法，是image matting的一种方法(lazy snapping algorithm is a method of image matting)
- 2008-01-31 22:03:57下载
- 积分：1
-
red-colour-tracking
the code is to track the lips. which need to be marked by red color.
the code tracks the red color of the lips and thus the lips indirectly.
such system can be very much useful for audio visual departments
- 2014-08-21 16:42:59下载
- 积分：1
-
re1
The model used for creating the reference voltage is shown
in Fig. 4. First, photovoltaic output current (Ipv) and output
voltage (Vpv) are passed through a first order low pass filter
with a magnitude of G = 1 and a time constant of T = 0.01
seconds in order to filter out the high frequency components
or harmonics from these signals as shown in Fig. 5 and Fig. 6.
The filtered current and voltage signals (Ipv_F and Vpv_F) are
then fed into the MPPT control block that uses the Incremental
Conductance Tracking Algorithm. An algorithm that is based
on the fact the slope of the PV array power curve shown in
Fig. 7 is zero at the Maximum Power Point (MPP), positive on
the left of the MPP, and negative on the right. The MPP can
thus be tracked by comparing the instantaneous conductance
(I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
- 2013-07-23 17:51:25下载
- 积分：1
-
freq_spec_lab08-(fundamentals!)
A doc about spectral analysis using matlab
- 2011-07-28 09:18:21下载
- 积分：1
-
HVDC_SynSTAT_Final
this is a simulation of HVDC system
- 2012-08-29 11:36:26下载
- 积分：1
