-
Josephson
数值模拟了一类重要的超导器件Josephson结满足的方程。整个程序用matlab编成。(numerical simulation of an important class of superconducting Josephson junction device to satisfy the equation. The whole process into using Matlab.)
- 2007-04-24 22:42:51下载
- 积分：1
-
Frank_signal_QPSK
产生脉内Frank相位编码调制信号，并对其进行平方、四次方变换，利用四次方FFT结果为单频信号的特点完成调制识别，最后绘图观察其瞬时相位曲线。(Generating pulse code modulation signal within Frank polyphase, and its square, four square transformed by FFT results for the fourth power single-frequency signal modulation characteristics of complete identification, finally drawing to observe the instantaneous phase of the curve.)
- 2015-03-15 09:05:31下载
- 积分：1
-
benggou
采用加权网络中节点强度和权重都是幂率分布的模型，在matlab环境中自动识别连通区域的大小,用于时频分析算法。( Using weighted model nodes in the network strength and weight are power law distribution, Automatic identification in the matlab environment the size of the connected area, For time-frequency analysis algorithm.)
- 2016-11-24 17:38:25下载
- 积分：1
-
RS_DECODER_V3_0
reed solomon decoder(matlab codes)
- 2008-04-18 16:36:49下载
- 积分：1
-
mydenoise
这是消除信号中噪声的程序，是国外编制的，比较适合初学。(This is the signal to eliminate noise procedures, the establishment abroad and are more suitable for a novice.)
- 2007-04-03 04:09:08下载
- 积分：1
-
micro-grid
Planned Scheduling for Economic Power
Sharing in a CHP-Based Micro-Grid
- 2014-08-22 19:06:52下载
- 积分：1
-
ApEn
说明： matlab计算信号近似熵，具体参数文件中有说明(Matlab calculates the approximate entropy of the signal, which is explained in the specific parameter file)
- 2019-10-29 20:02:29下载
- 积分：1
-
Two_degree_of_freedom_vehicle_model
说明： 如果对实际工程结构作简化处理，建立其动力学模型，并确定系统的质量、刚度、阻尼参数，便可以用多种方法建立系统的动力微分方程。常用的方法有直接 法、影响系数法、拉格朗日法以及有限元法等。拉格朗日法是从能量的观点建立系统的动能T、势能U和功W之间的标量关系，是研究静、动力学问题的一种方法。如果在选定运动坐标以后，能够设法求得坐标相对应的质量矩阵和刚度矩阵，就可以用影响系数法建立多自由度系统运动微分方程[4]。本文采用拉格朗日法建立了1/4车辆几何模型。(If the actual engineering structure is simplified, its dynamic model is established, and the mass, stiffness and damping parameters of the system are determined, the dynamic differential equation of the system can be established by various methods. The commonly used methods are direct method, influence coefficient method, Lagrange method and finite element method. Lagrange method is a method to study the static and dynamic problems, which is to establish the scalar relation among kinetic energy t, potential energy u and work W from the point of view of energy. If the mass matrix and stiffness matrix corresponding to the coordinates can be obtained after the motion coordinates are selected, the differential equation of motion of the multi degree of freedom system can be established by the influence coefficient method [4]. In this paper, 1 / 4 vehicle geometry model is established by Lagrange method.)
- 2019-12-23 16:13:14下载
- 积分：1
-
fuel-cell2
simulation of fuel cell -part3
- 2013-07-29 15:57:24下载
- 积分：1
-
car_pole_system_upload_ver
Reinforcement Learning 中以 Q learning 學習的倒單擺實驗。以x,x_dot,theta,theta_dot作為狀態參數 state，利用model模擬之結果做Q值更新，產生Q table，對學習平衡控制。結果以csv檔作為輸出，可以由使用者作圖觀察變化。(Reinforcement Learning , utilize Q learning for An inverted pendulum system control。x,x_dot,theta,theta_dot as state variable，use model result renew Q table，control learning of balance pole 。output csv file contain trail(times),balance time(sec).it s better observe the change if user plot it. )
- 2014-01-23 23:58:05下载
- 积分：1
