登录
首页 » matlab » ker_eval

ker_eval

于 2013-10-08 发布 文件大小:1KB
0 182
下载积分: 1 下载次数: 104

代码说明:

  该程序将高斯核函数做成matlab中的函数形式。当需要使用时加载即可使用,简单方便。(The program will be made in matlab Gaussian kernel function form. When you need to use to load to use, simple and convenient.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • turbo
    turbo编译码TD标准交织采用的是TD标准,码率为1/3(turbo code decode)
    2009-07-10 16:01:23下载
    积分:1
  • finger1
    matlab code to draw the chrometic component of finger
    2009-06-15 22:09:40下载
    积分:1
  • fecgm
    独立成份分析(ICA)以及winner滤波 Source separation of complex signals with JADE. Jade performs `Source Separation in the following sense: X is an n x T data matrix assumed modelled as X = A S + N where o A is an unknown n x m matrix with full rank. o S is a m x T data matrix (source signals) with the properties a) for each t, the components of S(:,t) are statistically independent b) for each p, the S(p,:) is the realization of a zero-mean `source signal . c) At most one of these processes has a vanishing 4th-order cumulant. o N is a n x T matrix. It is a realization of a spatially white Gaussian noise, i.e. Cov(X) = sigma*eye(n) with unknown variance sigma. This is probably better than no modeling at all...( Source separation of complex signals with JADE. Jade performs `Source Separation in the following sense: X is an n x T data matrix assumed modelled as X = A S+ N where o A is an unknown n x m matrix with full rank. o S is a m x T data matrix (source signals) with the properties a) for each t, the components of S(:,t) are statistically independent b) for each p, the S(p,:) is the realization of a zero-mean `source signal . c) At most one of these processes has a vanishing 4th-order cumulant. o N is a n x T matrix. It is a realization of a spatially white Gaussian noise, i.e. Cov(X) = sigma*eye(n) with unknown variance sigma. This is probably better than no modeling at all...)
    2010-05-27 23:08:51下载
    积分:1
  • 四旋翼飞行器在MATLAB中的仿真序quadrotors
    这是四旋翼飞行器在MATLAB中的仿真程序,包括simulink仿真系统和程序。(This is a four-rotor aircraft in MATLAB simulation program, including simulink simulation systems and procedures.)
    2021-03-29 09:59:11下载
    积分:1
  • FSK
    说明:  使用matlab软件实现fsk的调制与解调(fsk modulation and demodulation)
    2011-04-09 21:23:52下载
    积分:1
  • motorModel
    永磁同步电机的仿真模型,matlab文件,可实现闭环,计算力矩(model of permanent magnet synchronous motor)
    2009-05-11 00:23:32下载
    积分:1
  • dscdma
    DS-CDMA 通信系统的仿真,其中的信道为瑞丽衰落信道(Simulation program to realize DS-CDMA system)
    2013-01-14 14:35:31下载
    积分:1
  • barbershop_simulation
    this program implement barbershop in c++
    2014-11-07 17:56:34下载
    积分:1
  • concavefalt3
    平凹腔激光模式计算程序,利用边界元方法计算,matlab编程!(concave cavity laser mode procedures, the use of the boundary element method, the Matlab programming!)
    2006-07-03 19:39:42下载
    积分:1
  • Wind-turbine-blades-design
    本文利用MATLAB的遗传算法工具箱,对弦长和扭角沿风力机展向分布进行优化,得到设计工况下的最优叶片设计。目标函数是设计工况下基于动量叶素理论和Glauert等修正所得出的功率系数。在设计工况下得到的设计结果,其功率系数在一定的风速范围内都能保持一个较高的数值,同时其有效攻角分布大致都在所选翼型的升力与阻力系数的比值最大处,与理论相符合。其结果说明该优化实际的有效性。(In this paper, the use of MATLAB genetic algorithm toolbox, chord length and twist angle along the wind turbine development to distribution optimized to obtain the optimal design conditions blade design. The objective function is to design conditions based on the results of momentum blade element theory and Glauert correction power factor. Design results in the design conditions, the power factor within the range of wind speeds can maintain a higher value, the effective angle of attack distribution substantially in the the selected airfoil lift and drag coefficient ratio of maximum , theoretical analysis and show. The results indicate the validity of the actual optimization.)
    2013-04-21 14:06:41下载
    积分:1
  • 696518资源总数
  • 106148会员总数
  • 10今日下载