-
Butterworth1
Butterworth滤波器
内含一个文本文档，输入MATLAB后可直接运行
(Butterworth filter contains a text document, input can be directly run MATLAB)
- 2010-06-12 16:50:00下载
- 积分：1
-
kalkulator
Easy calculator dswafrefewfreqfr
- 2013-12-23 20:17:00下载
- 积分：1
-
donghua
用Matlab软件画出动画图，显示动画图的代码是一样的，只是具体的画图类型不一样。(Using Matlab software to draw animation showing the animation map code is the same, just not the same as the specific type of drawing.)
- 2010-02-17 11:55:46下载
- 积分：1
-
fenjiechonggou
小波分解与重构程序，小波的多层分解与从构(Wavelet decomposition and reconstruction process, the wavelet multi-layer decomposition and structure)
- 2013-05-17 22:40:32下载
- 积分：1
-
LEACH
以循环的方式随机选择簇头节点，将整个网络的能量负载均匀分配到网络中的每个传感器节点，从而达到降低网络能耗，提高网络生存周期的目的。(Cyclic manner randomly selected cluster head node, the energy of the entire network load evenly distributed to each sensor node in the network, which can reduce energy consumption and improve the life cycle of the destination network.)
- 2021-03-19 18:59:19下载
- 积分：1
-
2fsk
数字频率调制又称频移键控（FSK），二进制频移键控记作2FSK。数字频移键控是用载波的频率来传送数字消息，即用所传送的数字消息控制载波的频率。2FSK信号便是符号“1”对应于载频，而符号“0”对应于载频（与不同的另一载频）的已调波形，而且与之间的改变是瞬间完成的。 (Digital frequency modulation called frequency shift keying (FSK), binary frequency shift keying recorded as 2FSK. Digital frequency-shift keying is the carrier frequency to transmit digital information, that is, the number of messages transmitted with the control of the carrier frequency. 2FSK signal is the symbol of "1" corresponds to the carrier frequency, while the symbol "0" corresponds to the carrier frequency (with a different carrier frequency to another) and modulated waveform, but also between the change was instantaneous.)
- 2009-12-13 12:00:45下载
- 积分：1
-
Link-a-System-Level-OFDM-Simulator
针对OFDM系统，分成链路级仿真和系统级仿真两个部分。为了降低系统级仿真的复杂度，采用链路级仿真的部分结果。(It contains mainly two parts, i.e. link-level simulator and system-level simulator.
Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation.
System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.
Link-level simulator support SISO, 1 by x MRC, 2 by 1 STBC/SFBC, 2 by 2 Alamouti, x by 1 Antenna selection, x by y antenna selection.
System-level simulator, currently support only SISO and 1 by 2 MRC.
To start with, go into the folder sys_link_simu, and excute the following commond from matlab:
sys_link_simu_func(a,b)
where a is the link ada)
- 2011-08-09 11:00:53下载
- 积分：1
-
optim
This code is for optimization of radio parameters
- 2015-02-10 14:19:20下载
- 积分：1
-
HOSA-Toolbox
MATLAB高阶谱分析(Higher-Order Spectral Analysis )信号处理工具箱，有详细的安装说明。(MATLAB Signal Processing Toolbox higher order spectral analysis, a detailed installation instructions.)
- 2014-02-24 11:25:23下载
- 积分：1
-
A-Comparative-Study-of-Metaheuristic-Methods-for-
A Comparative Study of Metaheuristic Methods for Transmission Network Expansion Planning
- 2014-02-03 15:43:16下载
- 积分：1
